Jump to content
SAU Community

Recommended Posts

Already put the dash back together, where were you earlier when I needed you Dion? FFS :)

LOL, you shoulda gotten my phone number out of my Facebook profile :)

Unless I'm working I will go to Vilis tomorrow night, so I can show you how to do them if you want.

balls.

got the pump fitted, primed it, all was sweet, topped up the sump, turned the key, fired after about 5 seconds of cranking.

check for leaks.

gi-f**king-gantic leak spotted.

engine shut off 2 seconds later.

30 seconds of nosing around.

culprit found.

the spin on filter adaptor that outlaws assured me *would* fit, didnt sit properly. was impossible to see before hand, but basically, the o ring is sitting right on the lip of filter block on the engine.

lost a fair bit of oil in the 20-30 seconds it was idling.

taking it back in tomorrow to have a bit of a rant.

meh. at least its the adaptor and not the core or any of the huge number of fittings i have on that.

its undo 3 fittings, move lines, remove adaptor, mostly done.

as opposed to;

remove grill, remove headlights, remove front bar, remove intercooler, undo fittings, remove centre rad support strut, remove core.

do ppl pull the whole dash off to put the led's in? wow i only pulled out my centre bit.. took me all of 10mins to install my LED's

No, the pic I posted was when I ditched my bubbly dash in favour of a non bubbly one I paid $50 for :)

No, the pic I posted was when I ditched my bubbly dash in favour of a non bubbly one I paid $50 for :)

same. i hated the bubble, managed to score a 2nd hand dash for $100... badabing, problem solvered ;D

-D

same. i hated the bubble, managed to score a 2nd hand dash for $100... badabing, problem solvered ;D

-D

No bubbles in mine thank god.

So are people keen on something tomorrow night then since its too late now I dare say?

It wasnt really hard to find a replacement, mine came out of a GTR front cut. I have been told if they are not currently bubbly, that they wont go bubbly. Is there any truth in this? If I have to have my car parked in the sun I have a sunshade and leave both windows down about 1" and pray no bubbles appear lol

It wasnt really hard to find a replacement, mine came out of a GTR front cut. I have been told if they are not currently bubbly, that they wont go bubbly. Is there any truth in this? If I have to have my car parked in the sun I have a sunshade and leave both windows down about 1" and pray no bubbles appear lol

I've never heard that before, however there is a certain logic in that - the bubble only occurs when the glue deforms and the external layer separates from the framework - if you have a dash that is 20 years old already and hasnt separated, then chances are it'll be fine (touch wood - environmental factors notwithstanding)

Theres a guide on here on how to fix the dash but tbh I couldnt be stuffed doing it. I may end up getting an auto trimmer to redo my entire interior and they could probably reuse my old bubbly dash, remove the exterior (or cut and re-glue it) and then recoat the surface with lacquer, repaint etc..

My main issue atm is lacquering the hard upper weather strip - replacements cost $600 per side, so I'm hoping some resin will fill in the cracks and I can paint it gloss black to match the external surround

-D

Your doing a full resto style job on your GT-R ben,

When you sell it and pass one someone will be getting an extremely mint GT-R.

On the rear window the rubber, you know the little metal clip that sits almost perfectly in the middle, has anyone got one that I can grab, mines not there? lol

Your doing a full resto style job on your GT-R ben,

Yep. $20k i've spent on the GTR so far over the last 2 years. This does not count petrol or carloan, but it counts, raa, insurance, servicing, mechanical mods/replacements/upgrades, speeding fines etc.

When you sell it and pass one someone will be getting an extremely mint GT-R.

I won't be selling it. I plan to be riding this car for the next 20 years... probably will get written off by some tossarse whos not paying attention, but fingers crossed it lives as long as I do.... one of the customers at my mechanics is in his 50's, has had the same XB ford falcon with an intercooled supercharger since he bought it brand new as a young man.... I drool over it, even if the paint is shit and there are some ugly bits - its ghetto porn; naturally Im not gonna let mine get that bad, and there are more improvements planned yet, but its all a matter of money - no matter how much I earn, its never enough ;P

On the rear window the rubber, you know the little metal clip that sits almost perfectly in the middle, has anyone got one that I can grab, mines not there? lol

Dunno about that, speak to koji at japanese import spares in windsor gardens, he has damn near everything (and hes gotten me some great prices on door seals which I may go for depending on lukes contacts :)

-D

HAHA! awesome work that he was attacked.

Personally, i enjoyed the middle section of the article where it says " Will the premier Twitter about this?"

Oh dear god.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...