Jump to content
SAU Community

Recommended Posts

Nice R Jarred but you do realise that when you own an import you are forbidden to park any closer than 30cm to the curb so you never risk scratching your rims.

I will forgive this 1st offence but please be mindful of your proximity next time you park your car.

Thanks dude. But seeing as I've come from a 32 with the rims extremely hanging out of the guards I'm pretty careful when approaching gutters.

Mod list to check off in the next 6 months.

Kakimoto Regu 06

Tein super street coilovers

18x10+12 TE37

New air intake (can't even hear my BOV :laugh: )

Got the car back after getting the hubs painted and the calipers powder coated... also had my spoiler mounted again and took the front spoiler lip to get prepped for the riverland show... some pix

DSC00118.JPG

DSC00121.JPG

DSC00124.JPG

DSC00126.JPG

DSC00128.JPG

Few more touch ups required on the boot, the bonnet and the drivers door and a couple tiny dents on the passenger side. Not much more to go..

-D

because there abbo's and the legal system in australia is too scared of not being politically correct so f**ks like then get back on the street for the simple fact they are abbo.

all those scumbags have a criminal record longer sled's ban list, yet they still get all there benefit payments and go rob places such as vilis

edit: domar car looks clean as f**k, but plzzzzzz put a gtr lip on there :laugh:

Edited by rhys5169
all those scumbags have a criminal record longer sled's ban list, yet they still get all there benefit payments and go rob places such as vilis

hahah @ sleds ban list

edit: domar car looks clean as f**k, but plzzzzzz put a gtr lip on there :laugh:

yeah I did mention in the post that its getting spray painted atm ;P

-D

Well I just got defected. Done for cage, suspension, steering wheel. First defect on the car ever. Off to regency I go :laugh:

I feel your pain i got done last month they said my steering wheel was to small aswell but its withing the requirements...

So you are actually going to have the front lip on it? Thought you took it off because its only for "track cars"

no i took it off because i kept scraping driveways and speed humps and the like and i was damaging the shit out of it

as it is I had to get it bogged and sanded in many places

its going on for the riverland show, and then it'll come straight off until I can get some replacement suspension that increases my ride height by at least a cm if not 2

-D

its going on for the riverland show, and then it'll come straight off until I can get some replacement suspension that increases my ride height by at least a cm if not 2

Your ride height is far from low

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...