Jump to content
SAU Community

Recommended Posts

Thanks a lot for your responses :happy:

I have another question now.... When the time comes I will buy another R33, but the other day I was brousing the J-SPEC Imports website and came across some really nice cheapish r32 GTR's with around 60,000kms. Do you guys have any reasons why you would choose one over the other given the chance?? 32 is older but it's a GTR and I really like 33's so not sure.....

Cheers

haha i still have no idea what that sticker is, half the people i ask say its when you should and the other half say its when its done.

As for 32 gtr or 33 i'd say 33 just for the fact that despite the sheer sex of a 32 gtr, they are old cars. Get a 33 GTR, best of both worlds and then some :happy:

my sticker has the kms when the belt was changed written on it, not when it is going to need to be changed

the silver sticker is like a proper printed factory sticker with a line of Jap then underneath it has 100,000kms and more Jap...

are you saying yours has like 96,842kms or something like that instead? Or do you mean there's a different handwritten sticker there?

the sticker is simply there so to be written on when the car has had it's timing belt changed/100,000km service. I would not be buying a car that has no sticker on there as why would you remove it unless it has done >100,000km's/had it's timing belt already replaced...

Steve,

If you get a bad example of an R32 GTR it will cost you large amounts of money for repairs... GTR's are always going to be more expensive to modify, repair and maintain than GTST's as they have more to go wrong eg: 2 turbo's, 2 diffs, 4 axles, transfer case... etc.

GTST's arent as good as a race / drag car though for obvious reasons, also they are a lot more common than GTR's.

Bottom line... GTR is a better all round car, but its easy to get in way over your head money wise if you get a bad one.

GTST is cheaper, more common but still a great car for the price you pay.

Edited by Bullet32
GTST's arent as good as a race / drag car though for obvious reasons, also they are a lot more common than GTR's.

Of all the R32's I see getting around I reckon it's 90% GT-R versus 10% everything else R32.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...