Jump to content
SAU Community

Recommended Posts

hey guys, need some advice

recently took of some aftermarket parts to get my r34 gtt complianced. Then once everything was put back on (turbo,exhaust power fc) i obviously needed to tune the car again.

Anyway wont mention which shop i took it to as there extremely well known. But after watching one or two short dyno runs i left the shop only to come back and be informed that my apexi turbo which was in the car had blown.

Really f***ing pissed at the moment after they start pulling out bullshit like " it was bound to blow anyway etc etc"

which i know for a fact is crap for lots of reasons

1. turbo was inspected my people i know who are mechanics which told me i had scored a turbo in brand new condition

2. i drove the car in japan for at least three weeks on the boost it was dyno'd at (roughly 12psi) which should be jack all for an apexi turbo

3. also drove the car to the workshop and car was running fine

also as mentioned before first few dyno runs and the car seemed fine, according to them all it needed was new spark plugs and i come back to find they've blown the turbo.

at the moment there making it out as if it wasn't there fault

jsut wanted to know if anyone has had some past experiences like this and what my rights are.

Are they liable to fix/replace my turbo

thanks in advance for anyone who can help me

cheers

Link to comment
https://www.sau.com.au/forums/topic/188773-blown-turbo/
Share on other sites

i guess youll need to find the cause of the failure

there will be so once you find that then you can look at who is responsible

i mean if theyve gone and change your oil and water lines and left one off

and its cooked the turbo or theyve refitted your intake piping and one of the mech's accidently dropped a nut into the compressor snout and when they fired it up, its shat a cartridge then sure they are responsible. but youll have to certainly give good grounds for them being a fault. a tiny spec of dirt could get in the intake you use (if its a pod etc) and get into the cartridge bearings, which could cause failure. that wouldnt be there fault but you make think its defintely their faults. its a big grey area

Link to comment
https://www.sau.com.au/forums/topic/188773-blown-turbo/#findComment-3403319
Share on other sites

Of course they are going to say it wasn't their fault, because ultimately, it isnt.

Its your car, and performance does not carry a warranty, especially not for something they didn't even install.

Sounds like the motor has shit/poor oil pressure, or did have at once stage.

Turbo was damaged and then it eventually died.

It'd like to know how workshops said the turbo was 'Brand new" without seeing it sitting in a un-opened box, as there is NO way to be make that statement without pulling the turbo apart... which then means it'll need a full rebuild anyway.

Sounds like a case of hard luck, thats life. Its performance.

Put a new turbo on and get back on the road.

Link to comment
https://www.sau.com.au/forums/topic/188773-blown-turbo/#findComment-3403891
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...