Jump to content
SAU Community

Recommended Posts

Cheers for that sounds like i am running them a little to high then. Got to find a second a lap to give the GT2 a hurry up,

Will try that in the first practice tomorrow.

I want my slicks back, not likin these semi much now after not using them for 12 months :D

:D

Cheers for that sounds like i am running them a little to high then. Got to find a second a lap to give the GT2 a hurry up,

Will try that in the first practice tomorrow.

I want my slicks back, not likin these semi much now after not using them for 12 months :)

Ok thanks guys but its done and dusted now LOL

Got a first and a second placing against the GT2 in our 2 races so not to bad, got me by a half car length in the second race as my old girl pushed a little wide in third last turn....my fault not the old girl she did really well to be fair just need some good rubber under it and i will have him on a plate :P

going to try a dunlop DZ 02 i am told next time out see how they perform against the re 55. Anyone heard about them or used them. but thanks for the advice on the RE 55 i was at 36 and they were not good at all.

well done mate.

dz02 are about the same as the re55 (maybe a touch worse in the dry but better in the wet). But they have been superseeded by DZ03 which are better again. The DZ03 are the current tyre of choice among the tarmac rally guys

Thanks Duncan will post a few pic when they come through just for a few laughs.

Sorry i did mean to say DZ 03 was a typo was looking at them last night on the net, and while doing so i found these little numbers

http://www.tirerack.com/tires/tires.jsp?ti...odel=ECSTA+V710

what do you know about them if any as i had not heard of them before and i think as they are DOT legal i might be able to use them for the FIA GT3 racing week.

  • 4 weeks later...

That's the right site for the rim. No idea why it would do that, even when i hit 40psi hot at WInton the other week i just got lots of understeer, dropped the pressure for the next session and fine. No damage to the tyres.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...