Jump to content
SAU Community

Recommended Posts

alright, yesterday i was driving, my car temperature went up to HOT ... right up there. Therefore I stopped and saw a little steam comin out from the engine bay, on the left where the water is. I waited and then opened my radiator valve, and it was totally dry. I didnt have any coolant on me so i just put in some hot water. My car cooled down then i eventually drove to the coast. Did about 600km's soo far, and i checked today, open the radiator valve and it was dry again! TOTALLY DRY! However car hasnt overheated, because i havent driven it since. I thought it was a leak, however there was no water on the ground. What is happenin, please help

bryanlee38

Link to comment
https://www.sau.com.au/forums/topic/19035-keep-overheating-arh-help/
Share on other sites

sort of tune? - newbie (i dont getcha). Car's was dyno tuned by previous owner. I've had the car for a month soo far. I've filled up my car 6 times soo far. I've used ULtime and Optimax mainly, however i did use Mobil Premium unleaded once when i was desperate as i was on very very low fuel.

running stock boost. only mods r bov, pod, TT, 3 inch cat back, THATS it. nothing big. the radiator isnt leaking, no drips on the floor. THe water/coolant is meant to keep filtering back and forth Correct? ANy chance its just evaporating? I've only done 500km's and i have to top up. It has overheated once, but after the 500km's I check and the below the valve cap was DRY. but car hasnt overheated, I've refilled it with water. But will get coolant asap.

car hard to start?

Check the entire engine over for any sign of leakage whilst you run the engine from cold till warm. At this time check that the fan is working.

If you don't see anything then check your oil for signs of milky-ness.

When cool start the engine and run with the cap off.As it warms look for bubbles and signs of fuel contamination.

Take out the plugs and check condition for signs of water, (whiteness)

the car is a little hard to start, but I'm 99% sure its the battery. I'm gettin a new one on thursday. I've checked (well look at the floor) and there's no leakage onto the floor, can it leak onto anywhere else? the fan is working fine for sure. I checked the dipstickm, looks normal, however i did get my oil change yesterday, put in castrol magnotec

WHAT do u mean run with cap off - the radiator cap? What should it look like. currently where u r meant to pour the coolant in, i just have water in there. lastly, when u say take plugs out - what plugs

sorry. I'm new to this. only had the car for a month, slowly learning.

Check your oil for water.. Does it look sorta cloudy at all? That could prove that ur headgasket is gone..

Or perhaps ur head is cracked, or your hoses leak very slowly under pressure (ie engine hot). There are many possibilites...

If the coolant definitely isn't leaking out of the radiator, pump, hoses, etc (ie not leaking onto the ground through the engine bay) then it's going into your engine, simple as that. But check all the above again, as has been said it could be a leak that only happens under pressure.

I had a similar problem on my Commodore because it had a leak around the rear water jacket gaskets. Fortunately this meant it was a fairly slow leak (lost maybe 1 litre per month) and it was going straight into the rear pistons rather than the oil and simply burning off immediately as it seeped through.

I don't know if Skylines have a similar potential water jacket gasket problem, but if they don't then it would have to be the head or head gasket.

Whatever the case, it's time to visit a mechanic.

Yepp, could be the water pump.

How many KM's has the car done?

When they are on their way out, the water can seep out of the breather on the underside of the pump.

Usually they only leak when the temps are up and it's got presure behind it.

This mean that when the water leaks out it will evaperate straight away and just turn into mist, so you won't see any water on the ground :P and you'll be scratching your head for ages trying to find where the leak is....

Take it too a radiator place like RatRad etc. They can presure test the hole system and find out if it's the head gasket or water pump etc.

Good luck

J

It sounds to me like the head gasket or a cracked head if the engine is hard to start, turns over a little slowly. Water in the bores means the compression will be significatly raised for cranking.

I might suggest that you don't try to drive the car around until you have sorted the issue ,or risk bent rods or bearing issues which will make the whole deal very expensive.

If your battery is on the way out (as mine is) every morning the radio will have lost its presets and you will find that the power windows will go slower than a wet weekend. A battery that is not holding it's charge etc is VERY obvious so I would be pointing at head issues.

The spark plugs are what I'm reffering to, if you are a newbe then it would be time to have a mechanic look at it alternatively hook up with a local skyline australia forum member or two who is technical and offer a few beers to have a look. I'm sure there are a few guys in your area.

Had the same problem with my mates R32, only had it for a couple days then suddenly started overheating, It was the water pump, was leaking like a tap. You may only have a small leak under high temperature and pressure so maybe you won't notice anything while stationary.

We managed to get a brandnew water pump for $70. So the problem was fairly easily fixed.

I had a funny thing where i started to hear a really loud screeching noise.. I could see a little bit of steam forming on the windscreen. I opened the bonnet had a look around still hearing the screeching and couldn't see anything

It turned out to be a pin hole in the top radiator hose that due to the size you couldn't even see the steam.

if you want to check it at home.... fill it up with distilled water and then run it warm. to check for external leaks (hoses etc) squeeze the radiator hose (it should maintain pressure when the engine is warm). see if you can see any radiator fluid coming from anywhere when/after you do this. i had a pin prick hole in one of the plenum radiator hoses under the inlet (couldn't see it) and lost a lot of coolant that way

other thing is that internal loss of coolant can be caused by various things but it all comes out at the end (exhaust) so see if steam coming out and could be crack in head or gasket problem. also had this prob and was corrosion hole in head

so far I've done 1000km's since that overheating problem, car has been running smooth as. temp is goin strong. Since that 1000km's back and from the gold coast. I've put 300ml's of water in the radiator cooling system. I was thinking of just putting the coolant in and just see how the car goes for now, DO U THINK THAT's WISE? Like I've done 1000km's, if something was to go wrong, it would have (wouldn't it). But like i said it currently has tap water in there, should i just put coolant in and see how it goes ??? I know i should invest in a mechanic .... I think i will actually.

Don't waste your money on the coolant until you're sure the leak is fixed. You can get by with tap water, as long as you don't get caught in a lot of heavy traffic and don't go into the snow or something (for the boiling/freezing aspect).

Water will corrode your engine faster than coolant, but in the very short time you'll be using it until you visit a mechanic the amount of corrosion will be insignificant.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sorry, just assumed that talk of coloured pads meant EBC red/green/yellow/shit stuff. I don't know the DBA pads, but it's a reasonable bet that they will be OK. DBA make good stuff generally. Those 4000 series rotors I linked to are very good. I may well replace the RDA rotors I have with those when required.
    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
×
×
  • Create New...