Jump to content
SAU Community

Greddy T88-34d And T28 X 2 Turbos?!?

ArenaGTR

By ArenaGTR,
in South Australia

 Share

Recommended Posts

ArenaGTR Collaborator

ArenaGTR

Posted
Posted

Was looking through my garage just then, found these 3 turbos T88 and two turbos with "A/R 42 M24" writing on it (T28? GTR Turbos?)??

The question is how much can I sell those turbo for?!!? they are in good condition, no shaft play whatsoever, but it's just a bit dirty cuz it's been sitting there for like 2 years now...

Or do u guys think I should do a single turbo conversion in my upcoming R33 GTR? :whistling:

Link to comment
https://www.sau.com.au/forums/topic/190505-greddy-t88-34d-and-t28-x-2-turbos/
Share on other sites
Cubes Grand Master

Cubes

Posted
Posted

In my opinion TWINS FTW!!

Over a big single they offer better response. They do cost a tad more but factor in a new exh manifold, inlet modifications etc and there goes that saving from a big single.

Stick with twins; better response on that rolling acceleration out of a corner etc.

2 x GT2530's, dumps, cams, cam gears (spool), injectors, pfc, nice exhaust and you really can't go wrong. :whistling:

If your handy with a spanner pull the head off while its apart and drop a 1.5mm restrictor up front and replace the std h/g with a MLS type trust etc.

The restrictor prevents too much oil floating in the head during extended high rpm's (i.e mallala). If its apart you may as well; its not all that much more work to remove the cam belt a few head bolts and pull the head off. If not just ensure you keep the sump overfilled. :P

DRD-00F Grand Master

DRD-00F

Posted
Posted
more info please :(

The car is in NSW, fully built and forged engine, should hit about 1100hp without nos, and minimal lag due to the supercharger...

There is a LOT of info, that isn't even the technical side of it :P

img0522ma1.th.jpgimg0519wj2.th.jpg

I have some of it on the block with the supercharger, but they are at home...

If you want more info, ask here, or better to probably shoot me a PM...

Oh yeah, and it's not finished yet, but i believe it is close to completion...

ArenaGTR Collaborator

ArenaGTR

Posted
  • Author
Posted

Hmm, thinking of selling my Greddy T88-34D turbo as I won't be putting that turbo in my car hehe, how much can I sell them for? it's new I think, I will take some photos and post it up tomorrow.... and with my other two turbos hmm, it says Garrett A/R 42 M24 1-2, and what's that "1-2" meant? anyone?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...