Jump to content
SAU Community

Recommended Posts

specs, spool rods, cp flat top pistons, around 8.1 . crank polished and balanced,oil restrictor fitted.one oil gallery blocked off, trust sump, n1 oil pump, oilreturn rear of head back to sump.etc

http://s212.photobucket.com/albums/cc220/rockabillyrb30/

Edited by rockabilly
oh wait up did you drop it in with the gear box still in the car??? i have a gts4 with a gtr gear box so i have the same crap to go through as you just have. how long did it take ya?

hi mate took me 4 hours from start to finish. had to drop the anti roll bar and power steering cooler, but that was because i have a trust sump extension. i lined the gearbox input shaft up with the clutch then with a jack dropped the gearbox mount down and slid the engine on,quite easy really.

Edited by rockabilly

yea im having all sorts of trouble with mine. first time ive ever done anything like this. and i seem to suck at it so far. when you say aligned the shaft with the clutch is there some sort of an extension tool that u can slide on the spline of the shaft an then stick the other end into the clutch? eeeergh... i just know in the morning when i wake up im going to be up for headaches. really need a second person to work the crane while ya line it up. how long was your car off the road? also it looks like you rebuilt that yourself?? i take it your a mechanic then?

hi mate,no hang the engine off the crane so it slopes slightly rearwards. then lower in and guide the front shaft of the gearbox into the clutch then lower it in. you need to lower the gearbox rear so its at the same angle as the engine. then lower the engine in so it lines up.as you lower push the engine onto the gearbox keeping it all lined up. no i am not a mechanic, but yes i did build mine myself.. bernie

hey man

there is such thing as a clutch alignment tool, the best tool i have ever made was when i cut the front shaft off the front of my Nissan Blue Bird gearbox which i would put in the clutch and slide into the spiggot bush then tighten the clutch and make sure the shaft can slip in and out easily then your set for putting the box in properly in the car, it has to be nearly 100% to slide in first go.

yea im having all sorts of trouble with mine. first time ive ever done anything like this. and i seem to suck at it so far. when you say aligned the shaft with the clutch is there some sort of an extension tool that u can slide on the spline of the shaft an then stick the other end into the clutch? eeeergh... i just know in the morning when i wake up im going to be up for headaches. really need a second person to work the crane while ya line it up. how long was your car off the road? also it looks like you rebuilt that yourself?? i take it your a mechanic then?

fired the old girl up today, no water in her just a quick 5 mins,went first time on the button, no oil leaks just a little raspy for me,could be the forgies being new and all, will see what it like when the water goes in and she runs longer,, oil pressure 100 psi on 20/50 asda special

just done a 10 mile drive in it. i tell you guys these motors are totally different to drive than a 26, and the sound from my exhaust is unbelievable. smooth aswell. i get positive boost on the avcr from 2000 rpm any gear. thats with a turbo rated to 700bhp. well chuffed. when its run in and opened up ,man it will go some.its trying to go now and its only done 11miles.lol

well its done 60 miles now on the crap 20/50 multigrade oil, been to 1.1 bar @ 5500 rpm on that oil. just dropped the oil and put some mineral 15/50,s in will run that for a hundred and fifty miles and that will be the run in done..probably gonna be jan 4 when it gets mapped as the tuners nearby are all fully booked and i cant have time off in dec.

Sounds ace. Very well presented and good luck.

Hopefully my rb25/30 will be finished and on the road before Christmas.

Just something i noticed:

You air pod/filter has a reducer cone, then you have a silicon hose attached to increase the size to match the intake pipe. Wouldn't you be better off to remove the pod reducer cone and fabricate another cone to match the pod diameter and the intake pipe. Just thinking you may be causing some minor restrictions with the current set-up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...