Jump to content
SAU Community

Recommended Posts

Hi please see the ebay website, should you bid, please bid appropriately, it is a binding contractural agreement.

The car was bought previously and has been off the road for a while as i havent had any time to follow through with finishing the project off. It comes with the rear interior, roof lining, boot trim and tool kit. Wheels, subframes, doors, boot, wing, front seats, rear bumper, tail lights, side skirts are not included.

CAR IS SOLD AS A BARE SHELL

I am getting married and do not have the time to finish building the car up, i intended on building a circuit car out of it, but time has run out for me to finish the project. The vehicle had sustained prior damage in Japan, was fixed here in Australia, car needs a clean up. I repeat car has been previously damaged. Sold as parts not a car. Can be reregistered or used for race/rally purposes. Car is currently still registered and insured, also complied. I have compliance plates and registration to go with it also.

The shell comes with boot interior, tool kit, rear seats, rear plastic interior panelling, floor carpet, roof lining, fuel filler, fuel tank, rear window glass and quarter glass.

There are no doors, bonnet, fenders, subframes, suspension, wheels, front seats, boot, wing, side skirts, rear bar, dash, motor, gearbox, diffs, headlights or tail lights.

Please dont ask me questions as to whether parts are for sale as they are not.

Recently sold for $15,000AUD on ebay bidder never paid and furthermore is from this website. I would be seeking something close to this figure... It is registered and complied. Needs work to front end as it was hit in Japan and repair job looks rushed.

If you wish to bid the shell is on ebay, please bid appropriately.

You can pm me.

Cheers.

5xsbd08.jpg

6f7uo0j.jpg

4qf1dl0.jpg

5xnn639.jpg

5z71hu0.jpg

6bypobb.jpg

66e94sz.jpg

54iqma1.jpg

4ih6dza.jpg

Edited by GT51R
Link to comment
https://www.sau.com.au/forums/topic/191425-r34-gtr-v-spec-shell/
Share on other sites

To anyone interested in this vehicle, I currently have a complete (panel) GTR front end sitting in Japan.

071028_BNR34_Front.jpg

PM for details, best of luck with the sale.

no links to other auctions or other forums please mate. if you want to sell something here, describe what it is, where it is, and why it's for sale, and post a price. I'll give you a little while to ammend the ad. thanks. R

Bidder #7 is a joker.

Hes brand new to ebay and screwing around.

GT51R, tip for next time you relist it.

Put buyer requirements up.

Phone verification for all bidders with a feedback of 3 or less.

etc etc.

I also got an offer near Kailen's.

Yeah someone is playing sill buggers for sure, no point spending that much on a "GTR" (said figuratively speaking as there isn't much left to make it one) when you could buy an R34 GTFour and throw in the GTR running gear and still be better off than chasing up the billion pieces required to make this what it once was and may never be again.

Well if the bidder is a joker than he's an idiot as i have is address, my godfather is a business lawyer so if i dont get paid this time i am gonna summons the idiot, as i can sue based on the contractural agreement terms based on ebays signing up policy... I am not messing around this time, i want the money for my wedding. If another dickless piece of shit bids on it for fun then this time he/she will learn the meaning of financial pain. I wont let go this time... I gave full warning in my declaration of bidding on the item, hence i gave my duty of care...

Yeah someone is playing sill buggers for sure, no point spending that much on a "GTR" (said figuratively speaking as there isn't much left to make it one) when you could buy an R34 GTFour and throw in the GTR running gear and still be better off than chasing up the billion pieces required to make this what it once was and may never be again.

A gtfour resale or build up is not of the same value as that of a GTR which is already complied and registered... THe money you can make off it by rebuilding it up is in excess of $25,000 atleast. The car when put back together would cost only $14k or so and then you can sell it for $60k minimum!!! Cant do that with a GTfour, its suits a person who is a car bodybuilder and seller... Otherwise people cant see the usage for it...

Bidder #7 is a joker.

Hes brand new to ebay and screwing around.

GT51R, tip for next time you relist it.

Put buyer requirements up.

Phone verification for all bidders with a feedback of 3 or less.

etc etc.

I also got an offer near Kailen's.

The last dumbass who won it at $13,099 was a genuine person and had feedback higher than 3 etc... The person was about to transact until they couldnt get all the money...

Yeah, i understand.

Though you know those that a frauds on ebay don't use thir true name, address or any other contact information.

So Good luck finding him.

When your building a car though you don't think of selling it before you even start.

Ah well. Hope bidder #7 is good for you.

A gtfour resale or build up is not of the same value as that of a GTR which is already complied and registered... THe money you can make off it by rebuilding it up is in excess of $25,000 atleast. The car when put back together would cost only $14k or so and then you can sell it for $60k minimum!!! Cant do that with a GTfour, its suits a person who is a car bodybuilder and seller... Otherwise people cant see the usage for it...

That car shell is missing so many pieces the profit margin would be slim at best, the pictures still show it with a million more pieces than it has. If you want to make a quick $25K there are better/easier ways. The only thing GTR about it is the VIN number. It would be that much of a bastard to rebuild you'd need literally another complete GTR to scab bits off, only good if you've picked up something in Japan that can't be complied and you bring it over as the donor car.....even then I can imagine Mr Angle grinder would come out and the chassis numbers would mysteriously swap....presto complied

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...