Jump to content
SAU Community

New Act Member

Roo

By Roo,
in Australian Capital Territory

 Share

Recommended Posts

Roo Rookie

Roo

Posted
Posted

Hey guys and gals, i've just recently joined the the forums, and I'd like to introduce myself. My name is Roald, but you can all call me Roo.... its easier :)

Now, I don't drive a skyline, but i do have a RB30DET (25/30) in my VL Calais, and I figured this would be a good place to get some good info on the newer nissan tech, as the VL sites i've become accustom to are more 'SOHC oriented'....

I have some Q's regarding my setup etc. but I'll get to them at a later date (studying....)

Looking forward to getting involved,

Regards, Roo ;)

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/
Share on other sites
  • 4 weeks later...
Roo Rookie

Roo

Posted
  • Author
Posted

Ok, so its been a while.... I've been busy finishing my CIT course - flat out!

Here are some pics and info from the prevoius owner. I would have loved to do the conversion myself, but this came along and was far more cost effective :)

Engine

7,000 km's old

3ltr, acid cleaned, crack tested

bored and honed 50 tho to suit oversized pistons,

shot peened rods. New mains, big ends, small ends, balanced etc.

genuine Nissan head gasket

reconditioned RB25DET cylinder head with extra provision for VCT,

ceramic T3 turbo driven only on 6 psi

3inch exhaust with high flow cat

New bosch 910 fuel pump

Custom braided lines for turbo

Nizpro engine bay mounted intercooler

Wiring harness professionally modified to suit vl

Gearbox

R33 turbo 5speed manual box

Pulled down for inspection before fitting

Short shifter

Harness and speedo modified to suit vl

Heavy duty clutch,

shaved flywheel,

Fully balanced and modified drive shaft to suit r33 box

148RWkW and 530Nm on 6 PSI, std. R33 computer :)

Will get more pics up later on some time.

Cheers, Roo

post-43945-1196227870_thumb.jpg

post-43945-1196227880_thumb.jpg

post-43945-1196227887_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3502555
Share on other sites
Roo Rookie

Roo

Posted
  • Author
Posted
148rwkw? :huh:

Are you sure that figure is correct? You should be making a lot more than that...

No offence intended.

None taken :) .The reason for such odd Power vs. Torque figures is due to a rather restrictive intercooler. Between about 2100-3300 rpm I have access to full boost (10p.s.i), but by the time I've reached 4500 rpm its all the way back at 6 p.s.i :) You can see on the dyno sheet where the boost really falls off. Once its gets up on the revs, the cooler simply can't flow enough air.

Correct me if I'm wrong, but I think this setup should really start singing at around 4000/4500 rpm, right where its all over....

I'm condisering sending the cooler to Garrett for a recore (Nizpro tanks are good as far as I know?) and getting the turbo high-flowed/steel wheels. Any other recommendations? Will I need a fuel cut defender (sometimes it surges/cuts under boost at lower revs - i.e. full boost to manifold) or rising-rate reg?

Thanks for any input,

Roo

post-43945-1196474552_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3507884
Share on other sites
Bullet32 Veteran

Bullet32

Posted
Posted (edited)
None taken :P .The reason for such odd Power vs. Torque figures is due to a rather restrictive intercooler. Between about 2100-3300 rpm I have access to full boost (10p.s.i), but by the time I've reached 4500 rpm its all the way back at 6 p.s.i :( You can see on the dyno sheet where the boost really falls off. Once its gets up on the revs, the cooler simply can't flow enough air.

Correct me if I'm wrong, but I think this setup should really start singing at around 4000/4500 rpm, right where its all over....

I'm condisering sending the cooler to Garrett for a recore (Nizpro tanks are good as far as I know?) and getting the turbo high-flowed/steel wheels. Any other recommendations? Will I need a fuel cut defender (sometimes it surges/cuts under boost at lower revs - i.e. full boost to manifold) or rising-rate reg?

Thanks for any input,

Roo

If I may voice my opinion... :)

Well if you want to get the most from your engine set up (RB25 / 30DET) then I would suggest a fairly large low mount turbo such as a Garret GT30 / 82R, dont bother high flowing the one you have.

Im using a GT30 / 71R (slightly smaller than the 82R) and it is good for about 250rwkw, the larger GT30 / 82R will be better for your engine because you have more down low power because of the larger capacity and it will probably spool a larger turbo pretty quick.

If youre going for out right power then you will need a fuel pump - go for a Walbro in tank or Bosch 040. You'll also need to upsize your injectors as the standard ones will max out pretty quick, go for some SARD 550cc brand new squirters, dont bother having the standard ones high flowed.

As for your intercooler, I have been using a Just Jap / Cooling pro 300 x 600 x 76 front mount for a while and Ive never had a problem, I would highly recommend one for the price.

Get in contact with GCG in Sydney for the turbo, Powerflow injection for the pump and injectors and Just Jap for an intercooler.

Im using similar equipment in my RB25DET (550cc injectors, 040 pump, GT30 / 71R and JJR front mount) and my car makes 230rwkw and 550nm at 18psi, very conservative AFR and it has bugger all lag.

:D

post-17958-1196919715_thumb.jpg

Edited by Bullet32
Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3517303
Share on other sites
Roo Rookie

Roo

Posted
  • Author
Posted

Great, thanks for the info :P

For the moment its on hold due to a matter of funds, but I will definitely take your advice into consideration. I have been considering dropping the whole lot into an R32, but again this is more likely to happen later rather than sooner, once I finish my apprenticeship :P

BTW, anyone know what a good R32 rolling shell might be worth, just out of curiosity?

Cheers, Roo

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3524527
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a good German place in Brisbane if youre up for the drive 😛
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
×
×
  • Create New...