Jump to content
SAU Community

Car Cut Out

jake33

By jake33,
in Engines & Forced Induction

 Share

Recommended Posts

jake33 Experienced

jake33

Posted
Posted

Driving along today in rainy Melbourne and out of nowhere my car starts spurtering (kinda like jolting), so i slow down and it eventually cuts out. Fair enough...

I try and start it back up, starts fine, idles normally but when i rev it a little sputters and cuts out.

checked all plugs, cooler piping, battery, ect.. fine. Then i noticed my pod filter was a little wet and the induction tubing going up to the hole for factory intercooler piping was, is wet. Which is normal for a rainy day. Anyway i dried the area, waited about 30mins then started it up and it drives fine now. no prob

Could water have gotten into the AFM via the sucking pod and caused the cut out?? or should i be looking for anthing or other signs why this would randomly happen. car runs perfect now

any thoughts?

Link to comment
https://www.sau.com.au/forums/topic/192132-car-cut-out/
Share on other sites
jake33 Experienced

jake33

Posted
  • Author
Posted

yeah ive got the factory coilpack cover on it, didnt see any water or anything anywhere else. so random.

Ive driven it on other rainy days before, washed the engine at the car wash and have never had any issues.

its got me stumped

Link to comment
https://www.sau.com.au/forums/topic/192132-car-cut-out/#findComment-3454337
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...