Jump to content
SAU Community

Recommended Posts

I have read heaps of threads about rough idle, stalling etc etc and it seems to come up very often that intake leaks are the source of the problems.

Its pretty hard to find a small leak when the car is running by listening for it, especially with the noisy engine fan, and it can get messy with a can of wd40 or something similar being sprayed on every seal and clamp.

So I have been thinking about another way of checking for leaks.

Has anyone considered making a blank that fits inside the rubber hose on the intake pipe where it bolts onto the throttle body, and another blank that fits over the air flow meter where the fliter attaches. Then fit a rubber tyre valve stem into one of them and pressurizing the intake system to say 20 psi.

It would be a lot easier to listen for leaks this way when the engine is off. Also I was thinking you could not have a blank on the throttle body pipe, but instead put one on the dump pipe/exhaust tip and pressurize the whole intake/exhaust.

Can anyone see a problem with this? Im thinking of making some blanks up to check my engine but dont want to damage anything in doing so.

No problem, in fact i have seen kits for sale on the internet for this very purpose. I think it would work well.

I wouldnt go where the air flow meters are, i would go just after the turbos. Turbos them selves wouldn't be 100% sealed around the shaft.

Edited by GTR1993

Already been done before. Here's the general instructions.

You can do a leak test.

What you'll have to do is,

1. take your pod and AFM off.

2. use a baked bean can (full) and put it into your rubber intake pipe (assuming its still the stock one).

3. tighten up the hose clamp onto the tin creating a seal.

4. Open the throttle body with a brick on the accelerator pedal, so you can read pressure on the boost gauge.

5. take a hose that is plumbed into your intake between the turbo and the plenum or off the plenum itself.

6. Get an air compressor and pressurize the system through the hose and get someone to read the psi on the boost gauge. you only need about 5psi. you can use the compressors at the servos.

7. Listen for a leak. And use the soapy water in the spray bottle to find exactly where it is if need be.

It is easier to find a boost or pressure leak using this method because the car is not running and is easier to hear and locate.

Thanks for the feedback guys, it certainly seems a better way than trying to listen for a leak when the engine is running. Not surprised its been done before tho.

Funny to hear the different ways people use to plug the intake up. Maybe jam a spud in there, it works well up the exhaust :huh:

4. Open the throttle body with a brick on the accelerator pedal, so you can read pressure on the boost gauge.

I forgot to add, this is if you've got a mechanical boost gauge installed. But it will pressurize your plenum to check for leaks on it also.

Interesting you say this about pressurizing the plenum. This must mean that rb cams have 0 overlap. ie only intake or exhaust open at any time? Therefore pressurizing cylinders without losing pressure through exhaust ports is possible?

I did it on mine. My boost gauge is taking its signal from the plenum so I can only conclude its pressurizing it.

But i have heard of pressure being lost out of the exhaust which means they will have overlap.....I think.....enlighten me.

The rb25 plenum can be pressurized without the air leaking through the exhaust valves. I just tried it and the first time there was a leak, but i cranked it over a little bit and it sealed up. Removed afm, blocked the intake pipe, and pumped it up to 5psi through the fuel pressure reg hose that goes onto the manifold. :P

Did mine after some recent tuning issues and found a few small leaks. Got a piece of pipe and welded a hat onto it in to whichwe welded an air hose fitting and clamped it on behind the afm. Worked a treat and helped us solve a couple of niggle issues that has plagued us for a while.

I wouldnt do another build without doing this before it went to the dyno. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...