Jump to content
SAU Community

Recommended Posts

Hi all

I have a R34 GTT with the following suspension mods:

- tein super streets

- whiteline front (24mm) and rear sway (20mm) bar both on soft

- front and rear camber kits

- front castor kit

- aligned to SKs settings, pretty much everything is SK spec except coilovers and slightly smaller rear bar

Problem I am having is that when I take say a hard left corner, the rear seems to hop hop hop as if the rear passenger wheel is coming up and off and onto the road again. Its either that or the tyres are rolling on the side so much that Im getting that feeling. it is hard to explain but its like the rear of the car is hopping along to follow the cornering line.

The front seems fine to me and is well planted.

Any ideas what it could be? or what I should try to get rid of it? is it too much body roll?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/193750-rear-seems-to-hop-on-hard-cornering/
Share on other sites

does the car actually kind of buck? called pig rooting? happens in slower, tighter corners. and it happens when you are getting on the power just before the apex?

does the car actually kind of buck? called pig rooting? happens in slower, tighter corners. and it happens when you are getting on the power just before the apex?

Dont quite get what you mean by bucking BB? But im def. not getting on the power early

like as in the car is behaving as though it was a mechanical bull. ie jerking up and down as you are cornering?

I get that, but only on the street. I know my rear springs are too hard, but is there another reason it happens?

I seemed to have that problem at one stage :) my cars left hand rear shock had gone simple bounce test later and a replacement found and its been all good so far

it bounced around on tight corners but also on long sweeping corners at speed :) however it may have no relevance as i have a 33 but still thats my 2 cents hope it helps :)

Edited by SeanO
Were the Teins new?

You keep having weird problems with this car eh.

Are you slowing or accelerating through 80km/h during this corner?

Have you got a new bike yet?

Hahaha i dont really have any problems at all, i always think i do but its always fine in the end, i think its just my fussy self hahah

i think ive been pretty lucky to have everything go well with the car so far (knocks on wood)

teins are new, 1 year old, only done maybe 10 thousand km on them

its like a tight bend, im only doing maybe 50km/hr, maybe its just the nature of the bend, its one of those ones that get tighter as you get into it

naah still trying to sell the white cibby first, then onto a 600cc hopefully

i have exactly the same problem too. Theres a nasty winding road when i got to Bendigo its like a U turn on the middle of the hill and each time i turn it seems the tyres are slipping at the rears. Sort of felt like going into a dip and the car bounce back. I installed the tein read my signiture for specs.

Sounds like, insufficient rebound damping in the shocks to control the spring wind up caused by the rear squat on acceleration. Typical of a poorly matched spring rate and shock valving.

If you have adjustable shocks, try winding them up towards full stiffness. It sometimes helps.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...