Jump to content
SAU Community

Recommended Posts

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

yeah i was freaked out

we'd get one pide, finish it, then there'd be another, and another, and another....

great night fellas

bit disappointing that i woke up with pete's leg over my legs, but anyway, least i was warm all night. dutch oven action!

lol, we were all pretty well behaved if my sketchy memory serves me. we didn't even get booted which is a first. though we did get cut off which I guess is pretty much the same. Top night had by all. it's been far too long since I punished a kidney that hard. Kel is welcome back anytime. she kept up the pace pretty well. and it gives us some cred having a women there as without kels it's just a bunch of dodgey looking blokes with mo's that look like a village people revival group. with a lady present we can pass for hetro. nice :wave:

haha, no pics. It's too unkind I think. if you want to see what goes on, you have to come along. ever since this photo I've been scared off using a camera at all:

pic0521wx2.jpg

haha, no pics. It's too unkind I think. if you want to see what goes on, you have to come along. ever since this photo I've been scared off using a camera at all:

pic0521wx2.jpg

Oh dear god, here I was hoping that I would never see that picture again.

PATRIOT JOCKS MAN

it was good to see a new face adrian.

and yeah, dunno if I'd call it a stack really. more just nudged over a pint to see what would happen. the best part was when the bar chick came over and just said:

"well I'm not cleaning it up. do I look like a fking cleaner? don't worry about it it'll absorb"

she was tops. must have been all those 50c tips we left. Easto and I even got the odd free drink out of her. and how cool is this, she said when people come up short for the bill she just chucks in the rest out of the tip jar! nice.

it was good to see a new face adrian.

and yeah, dunno if I'd call it a stack really. more just nudged over a pint to see what would happen. the best part was when the bar chick came over and just said:

"well I'm not cleaning it up. do I look like a fking cleaner? don't worry about it it'll absorb"

she was tops. must have been all those 50c tips we left. Easto and I even got the odd free drink out of her. and how cool is this, she said when people come up short for the bill she just chucks in the rest out of the tip jar! nice.

Yeh top effort from the bar staff! Except when she she refused to come out and drink with us.. or did i just imagine we asked her that?

And remember It's PID --- EEEHH NOT PIE---DDDDD :wave:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...