Jump to content
SAU Community

Recommended Posts

i've been whoring the search tool on this forum and i still cant work out an answer.

very rarely the engine check light will come on, and when it does the knock sensor on the pfc reads pretty high. last night drove the car on a cruise for like 2.5hrs and knock sensor read 126 once. @ 4600rpm

during the night only saw it ever got to 40 @ one stage.

thing is i havent hear the engine ping inside the cabin.

some of the boys reckon i was shooting flames last night but thats just fuel dumping right when changing gears?

the car tuned @ racepace last year, and recently was retune there last month. b4 and after its pretty much the same, knock goes off rarely.

mods are TB 3" high flow cat, pod, cooler, 12psi, pfc and walbro fuelpump which is only 3 weeks old.

i'm thinking to get some splitfire coils, anyone got any thoughts?

Edited by eddieeeee-ro
Link to comment
https://www.sau.com.au/forums/topic/194037-pfc-knocking/
Share on other sites

if you are not experieicning any pinging, you dont have a plug/coil problem so i woundnt suggest you get splitfires. Knock is really to do with the tune, so your tuner should be able to sort it out for you.

Recieved PM: no probs ;)

Link to comment
https://www.sau.com.au/forums/topic/194037-pfc-knocking/#findComment-3480321
Share on other sites

i was of the belief that since he is not experiencing any detonoation, its merely the pfc knock sensor. ie, something to do with the tune? my bad then

probably is the tune i.e ignition timing advanced too much.

Link to comment
https://www.sau.com.au/forums/topic/194037-pfc-knocking/#findComment-3480363
Share on other sites

i was of the belief that since he is not experiencing any detonoation, its merely the pfc knock sensor. ie, something to do with the tune? my bad then

The knock readings on the PFC may or may not be actual engine knock. Sometimes a noise in the engine bay at whatever frequency the knock sensors are set to pick up will set them off. Regardless, the terms "pinging" and "knocking" are both detonation.

Link to comment
https://www.sau.com.au/forums/topic/194037-pfc-knocking/#findComment-3480371
Share on other sites

i've been whoring the search tool on this forum and i still cant work out an answer.

very rarely the engine check light will come on, and when it does the knock sensor on the pfc reads pretty high. last night drove the car on a cruise for like 2.5hrs and knock sensor read 126 once. @ 4600rpm

during the night only saw it ever got to 40 @ one stage.

thing is i havent hear the engine ping inside the cabin.

some of the boys reckon i was shooting flames last night but thats just fuel dumping right when changing gears?

the car tuned @ racepace last year, and recently was retune there last month. b4 and after its pretty much the same, knock goes off rarely.

mods are TB 3" high flow cat, pod, cooler, 12psi, pfc and walbro fuelpump which is only 3 weeks old.

i'm thinking to get some splitfire coils, anyone got any thoughts?

Just go back to Benno with that info mate.

If you tell him 4600rpm, what gear and roughly what load, it'll be one cell that needs adjusting and it wont take long

Also your more likely to notice the one cell at night, as the air is colder. Mine was similar ages ago.

Hit about 80 on a super cold night only around 6000rpm in 3rd, one/two cells changed and happy days ;)

Link to comment
https://www.sau.com.au/forums/topic/194037-pfc-knocking/#findComment-3480472
Share on other sites

Ive had my car tuned a few times,as mods were added.My car sometimes shows knock of 80 for a split second at high boost and RPM.

Taken the car back a few times to sort it out.But i was told all is normal.Could be a number of things in the engine bay making noise.

I never hear any pinging but i do get a read of 80 at high loads on occasion.

Tuner is very reputable.And works mostly on Nissans.

Link to comment
https://www.sau.com.au/forums/topic/194037-pfc-knocking/#findComment-3481134
Share on other sites

I been having same issue, Due to heat. + more boost. + advanced Timing. from the Manual 120(ish) knock indicates Detonation. In agreement with R21Nizmaid, tuner should be able to fix by adjusting the problem cells.. (which I really gotta get done :S).

Link to comment
https://www.sau.com.au/forums/topic/194037-pfc-knocking/#findComment-3484686
Share on other sites

a power fc reading of 125 is false, if it was correct you would definately hear it even if you didnt know what knock is. The knock sensor has picked something else up and like explained above there are many things that create the "frequency" that the knock sensor is tuned to detect, even rocks/pebbles being flung up into the engine bay can set this off.

If you are driving around with the normal max knock sensor of 40 thats ok. Anything around a true knock reading of 80 or so and knocking or pinging whatever you like to call is audible. You'll know when it pings, its a very distint noise.

To make yourself sleep a bit easier, stick it on the dyno and get a pull done just to double check afr's and knock levels

cheers

Link to comment
https://www.sau.com.au/forums/topic/194037-pfc-knocking/#findComment-3484834
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...