Jump to content
SAU Community

18s Scraping On An R32

julion
 Share

Recommended Posts

julion Community Regular

julion

Posted
Posted

I just got some 18s with 245/40/R18 tyres

the inside of the front tyres scrape on a metal piece (looks like part of the suspension)

It only really does it on hard conering, but is very off putting and Ive put my stockies back on the front.

Spacers kind of worked, but i was thinking about getting some smaller tyres?

is there any easy way to remedy this situation?

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/194083-18s-scraping-on-an-r32/
Share on other sites
BHDave Grand Master

BHDave

Posted
Posted
hitting stuff with a hammer sounds like a good plan to me :ermm:

does anybody know the bit the wheels are scraping on im talking about?

will it matter if i tap this with a hammer?

no, it's a f**king stupid idea.

I'm guessing it's the upright that attaches to the top of the hub and the upper control arm and the tyre is flexing on hard cornering. Which means your wheels must have a shocking offset in order to 1) fit 245's without scrubbing on the guard and 2) sit the tyre in close enough to the upright to give problems on turning.

If it's the bit i'm thinking of then i don't recommend it. Though to be honest i dont think you could do more than dent it as it's a pretty beefy unit.

roll guards, flatten seams, remove inner guards, go for it. don't go anywhere near the arms, hub or uprights with a hammer

adam-__- Grand Master

adam-__-

Posted
Posted

No way would I recommend knocking the hubs, swaybars or anything like that either, I was only talking about the guards.

I don't see how a wheel would rub against the hubs or uprights though. Only thing I would see it rubbing is the coilovers or brake calipers.

Taleb Tyres Proficient

Taleb Tyres

Posted
Posted
no, it's a f**king stupid idea.

Haha hey buddy i agree with you there, i dont mean going kamikaze with a hammer on the inside of the wheel area hoping for the best, Ive heard and dealt with enough of these problems to know that most of these issues are small easy fixes, most.

Depends where your problem spot is, get a pic if you can mate we can help you out more.

If your not sure where it is get a crayon or something similar and go over the inside edge of the tyre, or wherever you suspect its rubbing, drive around the block, have a look and see where its hitting..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      I transferred from full time service to Army Reserve, so I still have access, work has been super keen to get me in to work in the OPS realm, so just turning up to use the gym......and ovens, isn't causing any issues, apart from me needing to keep on telling them that I won't be doing any reserve days until I get my joint in Goulburn sorted  Basically I can now work whenever I want, for how long I want now, and it's all tax free Next time we have some fires or floods you might see me covered in mud, or cutting sick in some plant equipment cleaning up, the Reserves love getting in the news, LOL
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Final finish outcome of 80°c was typical to the pics, I've turned the oven down to 50°c and will pick them up after the gym tomorrow  The before and after difference was amazing, the wrinkle paint has covered all of the casting marks completely It did take a couple of hours to key it all and get in all of the crevices, but, for me it was time well spent for the final outcome, but I have all the time in the world to do it at the moment  Ended up with 4 coats, each sprayed at different angles to get optimal coverage and thickness As for the fixtures and intake box thingo that hasn't made it, the supplier is apparently posting the fixtures, and, are now sending a different CAI that is in stock The replacement CAI is actually better than what I originally ordered, but will require a pod filter that locates under the front bar, still serviceable, but it basically removes the whole OEM filter box and ducts into the front bar, so filter cleaning will require ramps and the removal of some front bar undertray, not a war stopper, just some ramps and an additional 10 minutes work every few months From looking at it it is made from alloy pipe from the throttle body, through the CAI hole in the rad support, then right turning under the bar, luckily the wrinkle paint was on special and I got 2 cans for $30ish, so the alloy will get the same wrinkle treatment as the intake manifold, hopefully it turns up soon, either way, the car will be getting booked in soon, if the parts aren't here, I'll just get MX5 Mania to " make it work"  
    • MBS206
      NC MX5

      By MBS206 · Posted

      I'm so glad base security is so high. I see they stopped some random codger from being able to just wander in off the street... 😛   PS, intake looks good!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So far so good, another hour and their done
    • RA708
      Is there a good place to learn how an engine works online?

      By RA708 · Posted

      Exactly how each part works and how they all work together to make the engine function. That's all I'd need to do a basic build. Maybe how forced induction works. I probably need to learn some of the maths behind it all as well.
×
×
  • Create New...