Jump to content
SAU Community

Recommended Posts

Gday All,

I am currently considering buying a set of coilovers (Tein SuperStreets) for my skyline but I am a bit unsure of a few things.

The main thing I am am concerned about is the legality of coilovers.

Obviously apart from the ability to lower you car below the legal limit, is there anything else which can cause them to be illegal?

Do the need to be of a certain shock design?

Do they need to be ADR approved?

I am in Queensland if it makes any difference...

Any help will be appreciated...

Cheers

ShanO`

Link to comment
https://www.sau.com.au/forums/topic/194555-coilover-legalities/
Share on other sites

as far as i know they are illegal for a few reason, i think one is ADR but the other is they dont have spots to hold the brake lines, in saying that there are plenty of cars that have them and dont get pulled up for it, so just make sure the car isn't too low and you should be ok

Let me rephrase that..............

Skylines have coil overs standard, the coil springs go OVER the shocks absorbers.

So coil overs are NOT and NEVER will be illegal.

Citroens have had in cabin height adjustment for over 40 years, so that can hardly be illegal.

Mercedes had and still do have height adjustment via aribags.

Plenty of late 70's Jap cars had in cabin adjustable shocks, so that can hardly be illegal.

What then is illegal? It is spelt out in the ADR's, too low (100 mm minimum) and less than 2/3rds of the original suspension travel.

Simplistically, if your R32/33/34 is lower than 355 mm at the front and 345 mm at the rear then it pretty much guaranteed to be illegal.

Back to the original answer, for less money you can buy a much better shock absorber than a Tein.

Cheers

Not sure about QLD but in NSW you need to have them engineered to have no worries, reason is say you get defected for ride hieght, all you do is go home and raise the car, clear it, then drop it again.

First thing a cop asked me when i raised my bonnet?"Your suspension engineered?"

(Apparently the engineer must measure the car at the lowest 100mm ground clearance, then destroy any residual thread on the coil over that would cause it to go lower).

there's nothing inherantly illegal about coilovers. most cars including skylines come with coilovers from the factory.

Gary....ouch.

Sorry, Matt was having a bad day, I have edited appropriately

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...