Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

They must expect us to just get around it. So it is more or less a waste of time for the exhaust shops and the car owner. Bloody EPA are just an inconvenience.

/begin rant/

so instead of catching the 40yr old falcodores and geninis that belch out massive quantities of crap, generally smoke and fart all over the place, the EPA and rozzers target the community who take pride in their cars. I treat my car as a hobby, it is immaculately looked after, doesn't miss a service, is always in tune to make sure it runs perfectly.

Similarly, council revenue raisers (parking tossifers) should instead of ticketing you and I when we're 2 minutes late for an expired meter be ticketing people who park across from single white lines, within 10m of an intersection, and generally park in dangerous places. This is where their power should be - improving safety for other road users.

I feel a letter to the editor of 'Motor' mag coming on...

/rant over/

Hey join the crew...

Anyway, all you got was a noise complaint, I wouldn't worry about that one. Take it to an exhaust place (box hill place was decent), and unless you're exhaust is too loud it will pass and you pay $27 for the test and they can sign it off - 30mins of your time. Mine was fully noise compliant at least, its just the other stuff i gotta get cleared.

Its all rubbish

Nathan - you got a Super Dragger II like mine so you'll be noise compliant... although of course it doesn't have to be a founded complaint either for them to sign it in and waste you're time. But like i was saying, if all it is noise, $27 test and you're back on the road.

Maybe they got complaints from the residents? BMT has had the same problem recently.

'coz it is .. HKS dump pipe, highflow cat, Super Dragger II catback on mine.. all tested to be just on 90db @ 5200rpm (i believe that is what he tested at) for the noise test an official EPA certified exhaust place with everything in place.

I knew it wasn't too loud. He said if it was just a noise complaint he could have passed it then and there although it was close to the limit. I'll find out for sure in a few days.

Often the smaller tip exhausts make more noise believe it or not. Things like the Apexi N1 are definitely over. A large number of the jap exhausts are.

Most likely was a cop, but it does say on there "an officer of the EPA" so it could actually be one of their own officers.

I'd say in this situation it was just unfortunate, wrong place at wrong time...but it does look as though Ice Performance has been targetted. 5:30pm - sit there around 4-6pm or so after all the people pick up their cars from there after work and pick them all off.

Hmmm, actually the BMT situation is sounding just a little too familiar in the space of a few weeks... What is going on? Are performance workshops themselves now being targetted???

Well compared to the $165 for a defect, its kinda less of a worry if you ask me. But yer, it can be used as yet another excuse to hassle us poor performance types :)

Although when i was getting mine looked at, I did notice some poor sod with some 1970's civic or something having his exhaust tested so its not just the nice cars :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...