Jump to content
SAU Community

Carsales.com.au's Review On The R35 Gtr In Japan.


Recommended Posts

the problem here is weight

as Ferni said, you can't go too far either side of optimal for the damping and have a system that works well

(ie- 'jacking' down or po-go'ing). the engineers have obviously chosen springs that have a huge rate to control the fat body, so that basicaly determines the ride characteristics. the shockies only job is to 'damp' the motion of the springs

also - I hope to god Nissan Australia does ABSOLUTELY NOTHING to suspension settings on account of MOTOR/Wheels magazine and the UK guys whining about comfort

:/

When the 350Z was released, the exact same complaints were made about its ride. So they revised the suspension for the European models, with help from Nissan UK. Guess what happened? Those suspension revisions ended up in later model 350Zs internationally, and everyone concluded the car drove better on the road since it was absorbing bumps. On road loops the Euro-spec setup was quicker and more confidence inspiring, and made the car more enjoyable to drive.

As always, the Japanese can't seem to tune suspension. They always assume "stiffer = better" when its not the case, especially not for a street car driven by ordinary people. A car with progressive handling is always quicker than something super sensitive unless you're a good driver (which most people are not).

Considering the car in question is not the V-Spec or N1, I hope they do something about the suspension if its as bad as they say. If someone complains about a track-focused car being too harsh on the road but great on the track, I'd agree that they're nuts, but if you intend on living the GT-R as a "daily drivable supercar" then I'd rather it absorb bumps and maintain constant tyre contact with the road.

As always, the Japanese can't seem to tune suspension. They always assume "stiffer = better" when its not the case, especially not for a street car driven by ordinary people. A car with progressive handling is always quicker than something super sensitive unless you're a good driver (which most people are not).

I thought the GTR used Bilstein suspension and was tuned by the guys at Bilstein?

Anyway, there is no way the GTR with its weight can lap the Nurg in 7:38 with softer suspension. Nissan engineers knew that and they had to compromise the softer suspension in order to get the lap time they were after.

I think you'll find that the differences between japanese-tuned suspension and australian-tuned suspension has more to do with the roads in each place than the engineers.

I love the term "built for australian roads" - in other words, have the suspension as soft as you can possibly make it so as not to spill your drink every 5m when you hit a pothole or some piece of badly cracked bitumen. Our roads (at least here in SA) are bumpy and extremely crap. On a good quality flat road, my stagea is more comfortable than just about every other car i've been in. It kind of just glides along, no seasickness etc.

But give it your average adelaide road and the suspension is less than perfect :P

As far as the article is concerned. Most of the aussie car reviewers are so brainwashed into aussie cars its no wonder it only scored 3.5/5.0. They were probably just confused because they couldn't work out what model of holden it was...

Correct me if im wrong, but the Aussie guy that test drove the GTR was from MOTOR magazine?

As i can recall, guys at MOTOR magazine have always been biased towards the GTR's - they don't like GTR's. There was one time, they tested the R34 with other cars and complained that it's handling around the track was more annoying than revolutional. Thats because they didn't know that a GTR is meant to be driven hard to bring out the best in it. They were driving it around the track like pussies.

However, WHEELS magazine have always loved GTR's. They were the ones that gave it the nickname 'Godzilla'. Anyway, i remembered an article where they tested an R34 N1 against a Monaro GTS or somethin and they said that the GTR was "the best car they've ever driven - no kidding".

Man these guys dont know how to drive pfft 4.0 wait till people own this car and get familiar with it easy mid 3s and mid to low 11s...

umm, with launch control and DSG what does the driver actually have to do to but hold the right pedal down???

umm, with launch control and DSG what does the driver actually have to do to but hold the right pedal down???

They were testing in slightly damp conditions. Hence there could be a couple of tenths that can be cut from the 0-100kmh time and the 0-400m (also mentioning they hit the 180kmh limiter before they reached the end of the 400m and they still managed a 12.1).

a) GT-R has launch control and b) it works! Using it to good effect on the complex's deserted dragstrip, in the failing light at the end of the Sendai session, MOTOR's David Morley punched out an even 4.0sec for the 0-100km/h sprint and 12.1sec for the standing 400m.

While in 'normal' conditions the 4.0sec will be hard to trim...

nothing about it being damp when they did it. If it was damp I doubt they'd say it would be hard to beat in normal conditions. so my point about knowing how to drive, or getting familiar with the car helping accelleration times significantly still stands.

nothing about it being damp when they did it. If it was damp I doubt they'd say it would be hard to beat in normal conditions. so my point about knowing how to drive, or getting familiar with the car helping accelleration times significantly still stands.

It seems you're right. did they mention what revs the launch control takes off? is it a clutch frying redline launch?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...