Jump to content
SAU Community

Recommended Posts

wrecking 1995 r33 series 1.5 nissan skyline

-it has a series 2 front which is no use has been smashed on the front and along the passenger side.

-has complete series 2 rb25det with complete engine loom and computer, turbo and lines, both manifolds, alternator power steering etc. engine has 68,000km's on it SOLD

- cross drilled and slotted front discs all calipers, rears have high performance pads- look like blitz ones (haven't checked yet) SOLD

-interior is still all good and in one piece except for driver's seat.

- has factory light up skyline boot garnish still in good condition.. SOLD

-series 2 rear spoiler with all LED's working $150

aftermarket parts

- genuine set of Nismo damper adjustable struts with matching Nismo lowered springs. all are straight and in very good conditon. SOLD

-has adjustable rear camber arms and front castor arms but need to check condition of these

- Nismo front and rear strut braces with brake stopper on front brace SOLD

-greddy profec b spec II boost controller- complete set up SOLD

-splitfire coil packs to suite series 2 rb25det SOLD

-complete stainless intercooler pipes including intake pipe for turbo that has port for plumback bov, replacement for standard crossover pipe and port for bov SOLD

-hks mushroom air filter with adaptor for airflow meter $50

- 3 inch mild steel dump pipe that joins to cat. SOLD

-Apexi copy pen style turbo timer SOLD

-genuine HKS super Dragger cat back exhaust 3 inch from cat to first muffler then 3.25 to resonator then 3.5 to huge stainless cannon with 5 inch tip. very good conditon SOLD

-Veilside side skirts RHS in good condition LHS has 2 small cracks which can be fixed easily. both painted in white. $150 pair

if your after any parts just ask and ill see what there is. pics will be up soon

pm or mark on 0433 960 414

Edited by 45ULT
Link to comment
https://www.sau.com.au/forums/topic/196423-wrecking-series-15-r33-skyline/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

sorry mate it says everything is ok in the interior except driver's seat which doesn't look straight after the accident..

intercooler pipes, dump pipe and door trims are sold.




  • Similar Content

  • Latest Posts

    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
×
×
  • Create New...