Jump to content
SAU Community

Recommended Posts

wrecking 1995 r33 series 1.5 nissan skyline

-it has a series 2 front which is no use has been smashed on the front and along the passenger side.

-has complete series 2 rb25det with complete engine loom and computer, turbo and lines, both manifolds, alternator power steering etc. engine has 68,000km's on it SOLD

- cross drilled and slotted front discs all calipers, rears have high performance pads- look like blitz ones (haven't checked yet) SOLD

-interior is still all good and in one piece except for driver's seat.

- has factory light up skyline boot garnish still in good condition.. SOLD

-series 2 rear spoiler with all LED's working $150

aftermarket parts

- genuine set of Nismo damper adjustable struts with matching Nismo lowered springs. all are straight and in very good conditon. SOLD

-has adjustable rear camber arms and front castor arms but need to check condition of these

- Nismo front and rear strut braces with brake stopper on front brace SOLD

-greddy profec b spec II boost controller- complete set up SOLD

-splitfire coil packs to suite series 2 rb25det SOLD

-complete stainless intercooler pipes including intake pipe for turbo that has port for plumback bov, replacement for standard crossover pipe and port for bov SOLD

-hks mushroom air filter with adaptor for airflow meter $50

- 3 inch mild steel dump pipe that joins to cat. SOLD

-Apexi copy pen style turbo timer SOLD

-genuine HKS super Dragger cat back exhaust 3 inch from cat to first muffler then 3.25 to resonator then 3.5 to huge stainless cannon with 5 inch tip. very good conditon SOLD

-Veilside side skirts RHS in good condition LHS has 2 small cracks which can be fixed easily. both painted in white. $150 pair

if your after any parts just ask and ill see what there is. pics will be up soon

pm or mark on 0433 960 414

Edited by 45ULT
Link to comment
https://www.sau.com.au/forums/topic/196423-wrecking-series-15-r33-skyline/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

sorry mate it says everything is ok in the interior except driver's seat which doesn't look straight after the accident..

intercooler pipes, dump pipe and door trims are sold.




  • Similar Content

  • Latest Posts

    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...