Jump to content
SAU Community

Nine Dead In United States Shooting Horror


Recommended Posts

Another one, all because he got fired from Mc Doanlds?

Article:

http://www.news.com.au/heraldsun/story/0,2...168-661,00.html

Gallery:

http://www.news.com.au/heraldsun/gallery/0...5006020,00.html

Edited by abu

People should have to sit an IQ test and a mental stability test before being able to get a gun. How many people have been killed because someone is just fkd in the head.

*shakes head* - another waste of innocent lives.

When will Americans learn that perhaps just because its 'my right' to own a gun, doesnt make it a good idea.

Guns should be illegal - perhaps that would end all the stupid pointless massacres that happen over there.

I wonder what the yearly statistics are:

Number of people dying from 'gun rampages' vs Number of people dying from "Al-Qaeda"

Stats would be interesting..

Having said that, the amount of violence that is on TV, Computer Games, and Internet is just not helping the situation.

I feel sorry for the families of these innocent people.

*shakes head* - another waste of innocent lives.

When will Americans learn that perhaps just because its 'my right' to own a gun, doesnt make it a good idea.

Guns should be illegal - perhaps that would end all the stupid pointless massacres that happen over there.

Yes because making things illegal immediately makes criminals rethink their whole lives and become mobile ice-cream vendors.

The worst shooting in Switzerland happened in a.......Gun Free Safe Zone :) those signs sure saved all those people hey?

Looking at most multiple shootings in the US they happen where registration and resrictions on conceal and carry have been enforced by the state and usually in 'gun free' zones.

:rofl:

Lucky it's not Victoria. They'd use it to justify more speed camera's :ermm:

Speed cameras, same logic but for a petty act.

Just another day is the US, some of these kids r so farked up

any1 else notice all the mistakes in that article?

"The disturbed teen's landlord said he was upset about being fired from his job at McDonald's and when she saw him with a gun last night thought he was going hunting with her sons."

"Television images showed paramedics taking a people on a stretchers into ambulances outside the mall."

"Jennifer Kramer and her mother hid in the men's department of Von Maur, praying that "God would spare us"."

"We heard about 35, 40 shots, and on our way we did see someone down by the escalator, bleeding,'' witness Jennifer Cramer told local television station KETV.

*shakes head* - another waste of innocent lives.

When will Americans learn that perhaps just because its 'my right' to own a gun, doesnt make it a good idea.

Guns should be illegal - perhaps that would end all the stupid pointless massacres that happen over there.

Most crimes are committed by guns that are illegaly owned or stolen, in fact if you own a gun and confront someone with it your are more likely to be shot by your own gun than you shooting them.

The whole gun situation over there is just out of control.

And they don't even do anything about it!

With the amount of guns they have on the streets there is not much they can do about it now, too little too late, have you seen bowling for columbine?

With the amount of guns they have on the streets there is not much they can do about it now, too little too late, have you seen bowling for columbine?

Yeah thats true.

Yeah have seen that movie, just shows that its one fkd up country!

You never hear of anything like that happening over here.

Edited by abu

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...