Jump to content
SAU Community

bumper support cutouts...

MaXiMuS007
 Share

Recommended Posts

MaXiMuS007 Mentor

MaXiMuS007

Posted
Posted

just wondering if anyone has a photo of what an r33 gtst bumper support looks like after its been cut for a 400r or GTR style bar?

send it to [email protected]

also is it possible to fit one without cutting the support at all?

Link to comment
https://www.sau.com.au/forums/topic/19700-bumper-support-cutouts/
Share on other sites
walkoau Mentor

walkoau

Posted
Posted

you should be able to fit a 400r bar with out cutting the bar support. i only cut holes in my support for the vent holes in the bumper either side of the number plate. sorry i got no pics of the support though.

skysaresilver Community Regular

skysaresilver

Posted
Posted

MaXiMuS007, if u get any useful information or pictures, could u please send them through to me also - it seems u are in the same position as i am at the moment - and was going to post the exact same question as u were!!! have u already got the 400R front bar??? if so where did u get it and how much did u pay - buying my kit in exactly two weeks, can't wait :)

please pm me or email me at [email protected]

Lepperfish Mentor

Lepperfish

Posted
Posted

I just bought a GTR front bar to suit the R33 gtst from unique auto sports and I had to cut a fair bit off the support out to fit it on properly, Its getting prepped and sprayed on monday so Ill let you guys know how it goes...

Cheers..

walkoau Mentor

walkoau

Posted
Posted

thats exactly right sly33.

Muximus007

if you already have the 400r bar try fitting it first without touching the bar support. i think you will be very suprised at how little you actualy need to cut. because the 400r bar is very deep at the front it should clear over the bar support and you should only have to cut out holes for the rectanglepieces either side of the number plate.

predator Grand Master

predator

Posted
Posted

Sly33.. i have the above bar.. GTR bar without the air holes..

My bumper support has been cut.. but its too hard to explain over the forums in words..

basically they cut the lower supports... the main part where it bolts onto the chasis was left.. they cut two rectangles into the support so that it bends more correctly across the bar..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...