Jump to content
SAU Community

Recommended Posts

Hi fellow stagea owners I NEED YOUR HELP!!! My stagea was steaming up alot and had a bad smell coming in from the vents then i noticed a wet patch on my passenger footwell OH NO! water was coming in from up in the well!! Im sure its the heater matrix which has gone, so im wondering if any of you guys can tell me do i need a stagea matrix or will any of the skyline or any other nissan ones fit and if so is it a huge job to fit it or can anyone have ago at it?

Any help will be gratefully apprectiated thanks.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/
Share on other sites

hey your heater core has gone by the sounds of it

go into the engine bay and disconnect the hose that goes into the firewall above the turbo heatshield, just under around bonnet height. probbaly best if I take a photo to show it.

I have heard you can use a 300zx heater core, I ordered one months ago for $220 and have never seen it (better check my visa card actually) so i cant confirm.

My local radiator peeps have quoted me $450 to rip out the dash and put back together, plus the core which is $500 from japan with new brass fittings

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3539171
Share on other sites

it's a biatch of a job!

i took mine out of my R33, and even with no intentions of putting the dash back in, it was quite a job.

you basically have to remove the entire dash, and everything in the way of the core...

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3539175
Share on other sites

dunno about a skyline one fitting, although the dash is a very different shape, but heater cores are pretty much the same regardless of make or model aren't they? You will only be restricted by inlet/outlet size, and what will actually fit in the hole left by the other one.

as for it being a hard job? To be honest, not really. It is a long, involved and fiddly job, but there is nothing that is very technically demanding about it. Same as everything else, if you take your time, pay close attention to how things come apart, and bag and label everything you take off, then you will be fine. I do recomend that you have a digital camera on hand to take photo's as you go - this can be an invaluable tool when it comes time to reassemble.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3539268
Share on other sites

Ditto on what Stinky Rooster said.

I've done this on an R31 Skyline and VC Commodore, except had A3 pieces of paper

on the garage floor with bolts laid out in position relative to the dash position.

Took 5-6hrs taking my time on a Saturday with a few ciggie/drink breaks in between.

Do it yourself take your time and save $$$$.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3539865
Share on other sites

Looked into this and was told by a well known Skyline tuner in the UK that the heater Matrix will come out into the passenger footwell. They reackon no more than a couple of hours to change !

Don't shoot the messenger as I have not done it myself yet.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3540470
Share on other sites

Looked into this and was told by a well known Skyline tuner in the UK that the heater Matrix will come out into the passenger footwell. They reackon no more than a couple of hours to change !

Don't shoot the messenger as I have not done it myself yet.

YEAH, I have heard that in an auto you can get to the heater core thru the glovebox area, but need to disconnect air conditioning and regass afterwards.

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3540494
Share on other sites

yes i can say taking the dash apart is a killer of a job, finding all those damn screws and clips is a job in itself :rofl: Good luck, dont forget there is a couple of screws in the demister vents and they are hard to see unless u look through from the outside of the windscreen. These 2 bolts prevented me removing the dash for a day as i couldnt work out for the life of me what was holding it on

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-3547241
Share on other sites

  • 1 year later...

Ive just taken my heater matrix out by removing the glove compartment then the a/c unit.

Its easy.You will have to get the a/c unit regassed. you can give the a/c unit a good clean as its out, mine was quite mucky.

http://www.skylineowners.com/forum/showthr...ighlight=heater

Link to comment
https://www.sau.com.au/forums/topic/198148-heater-matrix/#findComment-4987550
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
    • There is a warning that "this thread is super old" but they ignore that anyway...
    • With 10% Ethanol, we're talking 2-3% fuel consumption difference. The emissions reductions and octane boost in my opinion far outweigh this almost non existent loss.    My tanks sitting at 80%. Luckily that should go down fast as I'm on vacation again for the next two weeks. 
×
×
  • Create New...