Jump to content
SAU Community

Recommended Posts

After installing a hks GTRS turbo it now Feels like i am driving with handbrake on, and its low on power, it is slow through the revs no coughing or missfiring though, is the GTRS a laggy turbo the main reason i purchased it was because it has good hype for responsiveness. with standard turbo would have no dramas spinning wheels in take off and even into second now i cant even get them to chirp

I have an SAFC so shouldnt that rule out R&R??

When you upgrade to the GTRS was i meant to change injectors or Fuel reg??

Could it be fuel pump is not getting max volts??

supporting mods are

Bosch 040 fuel pump

FMIC

Blitz BOV

K&N pod filter

Splitfire ign coils

SAFC

3" turbo back exhaust with hi-flo cat

gizmo boost controller

Excedy HD clutch

Please any help would be great, after spending so much on turbo kit it is really ticking me off

Link to comment
https://www.sau.com.au/forums/topic/198243-problems-after-gtrs-turbo-install/
Share on other sites

it will need a tune and injectors and afm for you to see any kind of bennifit, remove the safc and get a tunable computer you have stepped up a knotch now and safc just wont do the job properly.

Check then double check all connections and gaskets you replaced.

Make sure you have done up all hoses/clamps and make sure all vaccum lines are on. Is the AFM plugged in?

I'm sure it will be something small and simple.

Good luck.

Check then double check all connections and gaskets you replaced.

Make sure you have done up all hoses/clamps and make sure all vaccum lines are on. Is the AFM plugged in?

I'm sure it will be something small and simple.

Good luck.

had loud whistle with new turbo so i have double checked and triple checked all gaskets and lines def no leaks, AFM is plugged in but i guess giving it a clean wouldnt hurt. didnt unplug any electrical connectors but will check nothing has come loose.

thanks

it will need a tune and injectors and afm for you to see any kind of bennifit, remove the safc and get a tunable computer you have stepped up a knotch now and safc just wont do the job properly.

They are selling these turbo's as direct replacements to standard unit, would have been good for a bit of fore warning to know i was goig to need management, larger afm and injectors.

my big problem is i would be happy if it was going as hard as before new turbo, but it is just so sluggish now

mate its normal. the car needs to be tuned.

when my hiflow first went in the car would take ages to boost and just felt crap.

another thing...... have you set up your ACTUATOR properly?????

bend it a little :)

(if you got the stock actuator ofcourse)

Edited by R33GOD

All those mods, and no fully programmable ECU - There is the problem.

Get a Power FC, and tune it

The GT-RS is an awesome upgrade for an RB25, and yes it technically is a direct replacement for the stock turbo, but common sense should tell you that when you replace a stock turbo with one thats rated at 420PS, you are going to need a suitable ECU to run the show, and the required supporting mods.

mate its normal. the car needs to be tuned.

when my hiflow first went in the car would take ages to boost and just felt crap.

another thing...... have you set up your ACTUATOR properly?????

bend it a little :)

(if you got the stock actuator ofcourse)

Bought Full HKS Kit came with actuator the lot,

just tighten it so it builds boost quicker.

i got one on my car. been ages since i stuffed around with it

It actually builds boost quickly but just runs like crap, i had a fuel pump fail on me and it felt like that, like there is just not enough fuel there, and when adjusting SAFC it is not making any difference

The std RB25 turbo is a bit restrictive on the exhaust side so going to a GT28 BB based turbo will open it up some .

I'd imagine the std computer is not giving it enough innitial light load ignition advance and thats making it feel a bit flat .

To have full control of fueling and ignition timimg you really need a programmable computer eg a PFC to take advantage of that turbos capabilities . I think exhaust/computer first is the best upgrade path because you can make the most of your engines spec at each stage .

Cheers A .

  • 1 month later...

Thought i had better update how i went with this problem incase anyone else runs into this drama,

Fitted a malpassi reg and seemed to fix the problem, but then it would intermittantly run like crap, so i put a fuel pressure gauge on and found it would vary pressure from drive to drive, I had mounted the malpassi on the side of the intake manifold and it was getting too hot, and when it would get hot the fuel pressure would fluctuate +/- 15%,

So i replaced it with a sard unit mounted it near the fuse box, new tune on the safc and hey presto car runs like a dream.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
    • They are in fact just nozzles. They are there only to produce a spray pattern and limit flow. The injector itself is what I use to control flow to the 7x nozzles. My old system had no injector and only PWM the pump. This lead to a lot of inconsistencies, and poor atomization at low pressure when the pump was ramping up. 
×
×
  • Create New...