Jump to content
SAU Community

Recommended Posts

just to chuck some more fuel on the fire, over in the states the nissan v6 comes out supercharged.

the Frontera and the xtera (like our pathfinder) run the vg and vq motors with a eaton blower between the V

we thought we would give it a go and picked up a few suitable parts off ebay, and bolted them onto my brothers pathfinder

running on gas and petrol at 5 psi we picked up about 40% of both torque and kws.

total price was around $800 which includes a bigger gas convertor. and the install took around 4 hrs.

ahhh well seing as this threads back up, migt aswell mention theres a guy in europe mid mounitng a ferrari V12 in one lol. certainly looks 'interesting'. f*ck knows where the pics are i saw it a couple weeks ago

weather it would work or not, would it be the kind of thing you would want to do in a gtir? dont get me wrong, i think they are great cars, i sure as hell wouldnt say no to one, but i mean, its small, not the most attractive car in the world and there a probably allot of cars out there that would be better suited and more at home with such an engine in it..

weather it would work or not, would it be the kind of thing you would want to do in a gtir? dont get me wrong, i think they are great cars, i sure as hell wouldnt say no to one, but i mean, its small, not the most attractive car in the world and there a probably allot of cars out there that would be better suited and more at home with such an engine in it..

I think the idea is that it is small and light. I own one and I know they are a little pugnosed but even without a turbo, i think a V6 version would stomp a R3x Golf into the ground.

it looks like the N14 Q is going to compact attack and maybe debut the GTiR at the same event :D

hope to bring mine down in full rally trim and see if I can spin the muddies for the length of the track :O if the V6 GTiR is running, it will probably have as much wheelspin as me but for different reasons hehehe

"The crazy thing is, it has one of the biggest turbos I have ever seen mounted just next to the gearbox at the front of the motor"

so the engines east west configuration from what ya say??

how can they possibly fit the gearbox anywhere unless its north south.

sounds like a complicated set up

  • 2 months later...

Its a late model nissan maxima fwd vq35 motor, usa sourced gearbox and a murano transfer case, the turbo according to the owner is a GT40R. The turbo sits above the gearbox and has been a monster on the dyno. He has had problems with diff ratios but is fixing that shortly. I'll link the pics when he gets them up :)

I am having the non turbo v6 fitted to my own rally car once he has perfected the conversion process :cool:

here some wierd and wonderful examples of engine swaps for ya

ATV motor bike powered by an sti motor

road trike with a porsche 911 motor powering it

1985 toyota hiux 2.4 desiel powered by a rb30det

1990 mr2 powered by a supercharged 2uz v8 motor

1993 toyota trueno/leven(AE111) converted into a rwd running a 2jzgte and six speed manual.

p10 4wd nissan primera running a rb20det gts4 driveline.

nissan laurel powered by a 450 big block with twin four barrell holley carbs

1994 5 door mitzi pajero with a 3litre twin turbo GTO or (3000gt as badged in aussie) engine in it.

and a v10 dodge viper engine crammed into a 1967 fibreglass replica of a shelby mustang.

There's a DC5 Integra that drifts in the US courtesy of a S2000 engine/driveline conversion.

Nissan UK has built motorsport Micras that have run mid-mounted SR20DETs and VQ35DEs.

Hartge has fitted a E39 BMW M5 V8 engine to a 1 Series.

There's a track-only BMW sedan that I've seen at an Eastern Creek day that runs an old BMW F1 1.5L turbo engine. Its not running qualifying boost, of course, but its still insane.

Some Elise owners in Europe slot the Rover V8 into them.

Some VW Van owners fit Porsche engines into the back.

No list of crazy engine swaps is complete without talking about the Bullet Roadster.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...