Jump to content
SAU Community

Aircon Regassers In Melbourne That Use Hychill Hr12 Gas

funkymonkey

By funkymonkey,
in Victoria

 Share

Recommended Posts

  • Replies 161
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

EliseViv
EliseViv

Not sure of the etiquette here....BUT IT F&^KING works :-) Cold cold air, and 33C and 50% humidity currently in Townsville and I am an ICY cool 40 something balding fat man in my 30 year old impo

RB335
RB335

To know if there is enough oil in the system, after running the a/c for a a while, you need to degas the system, remove the compressor and drain its oil, if you manage to drain about 20-50ml you know

RB335
RB335

I would put 80ml in there, half of it in the compressor and half in the discharge hose. 300 Sounds a bit excessive, I would think it would be more toward 220 grams, but unless you have a extremely ac

Posted Images

arep3 Experienced

arep3

Posted
Posted

not that much work to "convert" to HR12 unless the car has already been converted to R134a. if the car still has the old R12 gas in it, then it just needs to be tested etc. Degassed and regassed with HR12.

Ill have a quick guess at around $300 mark?

Someome correct me if im wrong please

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

hahah, tow car... you make it sound like something normal! should get the plates, A380 or something - if it's the massive beast i'm thinking of...

did you go with Hychill refill??

toygtr Community Regular

toygtr

Posted
Posted

Hey,

Haven't seen this before.

I've had my R32 GTR for 5 years now and have never had air con.

It was never gassed since it came over.

Where around croydon or ringwood does this regassing with hychill?

I also have got to get the pulley bearings looked at as they are very noisy.

Any suggestions on where to go?

arep3 Experienced

arep3

Posted
Posted
Hey,

Haven't seen this before.

I've had my R32 GTR for 5 years now and have never had air con.

It was never gassed since it came over.

Where around croydon or ringwood does this regassing with hychill?

I also have got to get the pulley bearings looked at as they are very noisy.

Any suggestions on where to go?

Hey.

The gas were talking bout is known as either Hychill or HR12.

A lot of A/C places will try to talk you out of it cos they dont know much about it themselves or have had too much R134a crap thrown at them to know any better. HR12 is essentially a natural refrigerant replacement for the old R12 systems that we have in R32's.

The HR12 works a lot better then the R134a stuff. Enough for you to cool a can in front of your air vent! it also wont corrode your A/C system like R134a does.

Sorry i dunno any places around your area that knows their stuff. I think my brother mentioned that his mechanic has it. ill find out soon.

Good luck finding a place.

I didnt really get a chance to talk to ya at the midnight cruise apart from trying to figure out where we were!. will hafta talk properly next time.

toygtr Community Regular

toygtr

Posted
Posted
Hey.

The gas were talking bout is known as either Hychill or HR12.

A lot of A/C places will try to talk you out of it cos they dont know much about it themselves or have had too much R134a crap thrown at them to know any better. HR12 is essentially a natural refrigerant replacement for the old R12 systems that we have in R32's.

The HR12 works a lot better then the R134a stuff. Enough for you to cool a can in front of your air vent! it also wont corrode your A/C system like R134a does.

Sorry i dunno any places around your area that knows their stuff. I think my brother mentioned that his mechanic has it. ill find out soon.

Good luck finding a place.

I didnt really get a chance to talk to ya at the midnight cruise apart from trying to figure out where we were!. will hafta talk properly next time.

Yeah cool, will have to chat next cruise.

If you could find out where a good place is that can do my air con let me know.

I dont mind a drive, if it gets done properly.

Cheers.

STATUS Grand Master

STATUS

Posted
Posted (edited)
hahah, tow car... you make it sound like something normal! should get the plates, A380 or something - if it's the massive beast i'm thinking of...

did you go with Hychill refill??

the two most reputable people is spoke to talked me out of it..... gave me the option but i ended up going R134 :happy:

Stupid A380 needed new hoses, TX valve and receiver drier been open for too long.... i wanted the a/c to be perfect so took to anything that could be suspect... lucky the conversion used xf falcon gear so its only the hoses (20ft of hose :D ) that is dear.

Attached a pic of what it should look like once finished. 10 stud FTW

post-34927-1257941082_thumb.jpg

Edited by URAS
AnDyStYLe Community Regular

AnDyStYLe

Posted
Posted (edited)

As stated in an earlier post (although in 2008 lol), JNK Auto does HyChill...

I just called them up now and spoke to Tim. What a champ, he spent like 20mins chatting to me about it explaining it all. Good thing was he was honest and said he is still acquiring his licence to do ac gassing and he doesn't personally do it, his boss does (John). Shows to me he's pretty clued up even though he doesn't personally do it.

Anyway, I'm book in for next week. Their contact number is 9873 2622, located in Mitcham.

Cheers,

Andy

Edit: Quoted $132 GST inclusive for the full works (i.e. full flush, lube and dye, and recharge etc.).

Edited by AnDyStYLe
toygtr Community Regular

toygtr

Posted
Posted
As stated in an earlier post (although in 2008 lol), JNK Auto does HyChill...

I just called them up now and spoke to Tim. What a champ, he spent like 20mins chatting to me about it explaining it all. Good thing was he was honest and said he is still acquiring his licence to do ac gassing and he doesn't personally do it, his boss does (John). Shows to me he's pretty clued up even though he doesn't personally do it.

Anyway, I'm book in for next week. Their contact number is 9873 2622, located in Mitcham.

Cheers,

Andy

Edit: Quoted $132 GST inclusive for the full works (i.e. full flush, lube and dye, and recharge etc.).

Excellent mate.

Will give them a call for sure. Thanks.

AnDyStYLe Community Regular

AnDyStYLe

Posted
Posted (edited)

Ok guys, doing the whole works including fault testing, full flush, change of receiver dryer, and gass fill...

John mentioned that they is not point doing the full works if you don't change the receiver dryer as it acts as a filter. All up if all goes well it'll actually be about the $220 mark!!!

The lubricate they'll be using is Wurth Ester Oil with U/V Dye (http://www.wurth.com.au/catalogueview.asp?pdf=A04_0601.pdf). Just done some research and found positive reviews. Better than PAG oil.

Will keep you all posted...

Cheers,

Andy

Edit: Ok, now found that POE = POE Polyolester (type of oil for A/C) according to acronyms.thefreedictionary.com, so if I'm not wrong that means the Wurth Ester Oil with U/V Dye is POE which is what level323 recommends. Hope that's the case!

Edit #2: Found the MSDS for the Wurth Ester Oil with U/V Dye - http://www.wurth.com.au/msds/1892_764_334.htm

Edited by AnDyStYLe
AnDyStYLe Community Regular

AnDyStYLe

Posted
Posted

Ok boys, update...

Ran into issues with the a/c where we found out that the a/c compressor sh!t itself... My options where either to repair, replace brand new or second hand. 1. Repair was going to be like $500, 2. Brand new $1k :P , 3. Sourced my own second hand unit for $100 :(

So anyway, I picked up the compressor on Friday morning which we only found out this morning when the original one was removed to be replaced, it was the wrong one. Needed to go back to the wreckers to exchange for the correct one...

Anyway, to cut the long story short... John/Tim from JNK Auto sorted it all out today and has done an excellent job. I am bloody wrapped!!!

All up I spent $260 to JNK and $100 on the second hand compressor. I gotta say JNK looked after me pretty well and would recommend them for sure!

Unfortunately John wasn't too keen on a "group buy" as in his past experiences, many of the people in the "group buy" ruin it for the others by not turning up. John would prefer a individual case by case like mine.

Cheers,

Andy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...