Jump to content
SAU Community

Recommended Posts

Hey all, i have just installed this kkr 480 turbo i had at home. i have found that for some reason even with the actuator rod not connected the car still running boost, i guessing the size of wastegate hole is to small..correct me if im wrong???

has anyone had this problem??

also have i got the kkr430 and maybe this is the problem ?? but im 90% sure its the kkr 480 someone gave it to me so...

cheers.

Edited by rich flavour
Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/
Share on other sites

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

with the actuator disconnected, the wastegate will never open, which means boost will continue to rise as long as the throttle is open and the engine is ingesting air

this basically means your running unlimited boost - be careful with this - it might go bang.

what spring are u using in the actuator? what boost controller have u got setup?

what exhaust setup do you have? have you checked the actuator / swing valve for play? does the wastegate flap actually open?

Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/#findComment-3564299
Share on other sites

Hey all, i have just installed this kkr 480 turbo i had at home. i have found that for some reason even with the actuator rod not connected the car still running boost, i guessing the size of wastegate hole is to small..correct me if im wrong???

has anyone had this problem??

also have i got the kkr430 and maybe this is the problem ?? but im 90% sure its the kkr 480 someone gave it to me so...

cheers.

youve gotta get it machined out mate to a bigger wastegate hole and flap MTQ doit or any other turbo place i had to doit to my kkr430

Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/#findComment-3564303
Share on other sites

i also get the same problem my kkr480 i just had it put back onto my rb25 and i also put on a greddy plenum and last nite i seen 1.46 bar so that cant be good hmmm

b4 the plenum upgrade it was around 1.2bar i would hit...

Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/#findComment-3564324
Share on other sites

im sellin the kkr setup soon and im selling a real good Greaddy td06h-25H polished turbo with top mount mani and gready dump pipe, if u want this will spool fast n pull very hard all the way unlike the kkr that kickes in way too late on such high boost.. let me know if intersted

Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/#findComment-3564451
Share on other sites

with the actuator disconnected, the wastegate will never open, which means boost will continue to rise as long as the throttle is open and the engine is ingesting air

this basically means your running unlimited boost - be careful with this - it might go bang.

what spring are u using in the actuator? what boost controller have u got setup?

what exhaust setup do you have? have you checked the actuator / swing valve for play? does the wastegate flap actually open?

The spring on the actuator is factory kkr, exhaust 3inch after market turbo back. i have checked the actuator it functions fine, tryed with 2 diffrent boost controllers one electric the other just a cheap t piece style same resault. i have also tryed with no boost controller does anyone no the least boost you can run with this actuator??

so wastegate hole is to small thats my problem?

Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/#findComment-3564681
Share on other sites

im sellin the kkr setup soon and im selling a real good Greaddy td06h-25H polished turbo with top mount mani and gready dump pipe, if u want this will spool fast n pull very hard all the way unlike the kkr that kickes in way too late on such high boost.. let me know if intersted

How much you want for this turbo mate? what state you in? how manys k's has it done? and at what boosts? what sorta power can i expect to make at the wheels??

Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/#findComment-3564687
Share on other sites

i also get the same problem my kkr480 i just had it put back onto my rb25 and i also put on a greddy plenum and last nite i seen 1.46 bar so that cant be good hmmm

b4 the plenum upgrade it was around 1.2bar i would hit...

what do you rev your car out to or you dont flogg it when it isn't running right?

Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/#findComment-3564693
Share on other sites

limiter is set to 7500rpm im pretty sure, but since plenum upgrade and car hasnt been tuned, ive lost alot of down low and turbo comes on really hard bout 5000rpm and then goes straight to limiter...

sounds gay if the boost range is 5000 to 7500rpm is it evan worth it?

Link to comment
https://www.sau.com.au/forums/topic/200257-kkr-480-on-r33/#findComment-3565729
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...