Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

They rank up there with fake bov's... but if you're dead set on looking like a tool, goto any nos or nxexpress installer and ask them to hook you up with a CO2 rather that Nitrous Oxide purge kit.

Might as well go all out get the Nitrous Oxide nozzles installed and a bottle warmer, at least it won't be all show then >_<

he didnt ask you what you thought of it. Or your flaming.

He just asked where he can get it from..

All of you guys just jump on the bandwagon and start flaming because YOU think it's gay.

tis called freedom of speech my friend, maybe we could talk some sence into him

he didnt ask for your particular opinion on flaming in this thread either but you still gave it

lol

install a t-piece on your radiator hose. install a thin heat resistant tube into said t-piece. run this tube into a windscreen washer nozzle. drive up and down the road at really high revs till your engine's really really hot. activate nozzle. watch as your ghetto fake NOS inflicts damage to your car's paintjob and delivers amazing 3rd degree burns to your face. it'll cost you about $20 in supplies. good luck.

install a t-piece on your radiator hose. install a thin heat resistant tube into said t-piece. run this tube into a windscreen washer nozzle. drive up and down the road at really high revs till your engine's really really hot. activate nozzle. watch as your ghetto fake NOS inflicts damage to your car's paintjob and delivers amazing 3rd degree burns to your face. it'll cost you about $20 in supplies. good luck.

fknlol! :woot:

LOOOL :P

is it that bad??

woops, i didnt know... lol...

I was just thinking of the 2F2F movie, and finally found out what those systems are called. :D

From what i know the only point of a purge valve is to purge air and vapour out of the lines so that the liquid nos fully fills the lines... Its basically only used (properly) by extremely high end drag cars which need every last bit of performance.

Most people who are into performance cars know this, so therefore when they see a dude in a stock looking R33 purging what appears to be nos, they instantly think -POSER- Your car doesnt need that mod for any reason other than to try to look cool.

To make matters worse, you're talking about putting a FAKE version of a pointless modification onto your car. Thats twice as bad! :banana:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...