Jump to content
SAU Community

Recommended Posts

Hey everyone,

My 32 GTR has a problem, it has all your basic mods, n1 turbos etc etc.

Today it started doing a few funny things. When I a accelerate, the car might hit say, 2500-3000 rpm then start stuttering/hesitating,

i'll put it in 2nd, and it might hit around 4000rpm and just cut out, as in stop accelerating all of a sudden. If I play around with the gears,

the car will get moving again.

And sometimes, it runs real good, in 1st/2nd, but 30 secs later it will have the hesitating problem, the car gets stuck at a certain RPM and refuses to budge,

unless I shift up or down. And it even almost stalled once, revs dropped to 0, i tapped the accelerator right before it would have stalled. It is strange that i cuts out completely,

usually, if a car pings, you keep accelerating, it will hesitate, but get through the rev range. Whereas in this case, it does not.

Going to the mechanic tomorrow, but has anyone had this problem before, in case it is something simple I can fix.

Thanks.

Edited by IOWNU
Link to comment
https://www.sau.com.au/forums/topic/200879-r32-gtr-running-poorlyhelp/
Share on other sites

umm sounds very similar to my issue and i have followed the tut on cleaning the afm and checking the solder.. still happening.. does anyone know voltage the afms should be seeing normally

Just change the AFM, no point stuffing around with a stuffed AFM.

I had to change 1 and now its running fine.

Thanks for the help guys.

the power supply to the ignitor and the earth wire at the back near the ignitor...check those harnesses..had the same problem with same symptoms with my old GTR....bcos i was getting the coil cover resprayed had to move the wires and cos its older car the wires can become hard...and think thats was caused mine to cut out etc as above

hope that helps if it isnt the AFM

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Why are people so insistent on making dirty water?!
    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...