Jump to content
SAU Community

Recommended Posts

Hey all,

I got a r32 gtst-t RB20DET and a few weeksago it was running on 5 cylinders. I unplugged coilpacks one by one and found cylinder 2 was no go. I pulled out the sparkplug and coilpack and cleaned them, put them back in and it was good.

Its just happened again. Yesterday i change oil filter and oil. Then regapped plugs from 1mm to 0.8mm (with feeler gauges) Then started car and it was running on 5 cylinders. Checked them and it was cylinder 2 again. So i bought new plugs and put them in and still same thing. Then i pulled the coilpack off sparkplug and left it connected, started the car and it was definately working as electricity was coming out.

Still no good.... so i compression tested motor and it has 150psi across all cylinders. What could be happening?? Im thinking maybe the igniter??

I bought splitfire coilpacks.. on their way.. but im geussing they dont have a new igniter. Are there any cheap aftermarket igniters? Are r33 and r32 igniters the same? Or is it definately not the igniter///?

cheers

Link to comment
https://www.sau.com.au/forums/topic/201215-rb20det-cylinder-2-no-go/
Share on other sites

i changed the plugs thinking they may be at fault.

The coilpack is sparking but some one PM me and said its easier for coilpack to spark to atmosphere than it is when its inside engine..

As for the loom.... i have llooked but not many wires are uncovered... i will try a mates loom and see how it goes..

also a question... i had the coilpack plugged into loom but not on sparkplug... turned the car on and sparks were coming from underneath where i expected at bottom of stem... but also at the top... is this not right?? Or is it meant to spark there too. Im guessing its not. Ive been told to put silicone on my coilpacks to increase their performance but never understood what they meant... im thinking maybe put silicome at the top to stop loose sparks??

thanks

ok... so still having troubles really in need of help.

Sum it up... cylindr 2 is not firing still. I know this cause when i unplug cyl 2 coilpack look it stays same (running bad) then any others makes it worse.

Remedies i have tried to fix it but to no avail..

Brand new Colder NGK Spark Plugs

Brand new SplitFire coilpacks

Igniter off a working skyling

Coilpack loom

Compression tested to 150psi

STILL NO GOOD!!!! What else can it be!! Im in dieing need. Please help

Have you checked that its not fuel that is the problem in #2?

Is the injector firing?

jus spoke to mechanic today nd he said to check if injectors r running. I dnt really know what im looking for but i geuss ill put a pices of steel rod against injector and use it as a stethascope (sp) and listen for a little tick. If number 2 had a dull sound it obviously isnt wrking correctly. But he said it still might tick but fuel just might not be getting through.

Ill check this sometime tomoro or sunday and post up.

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...