Jump to content
SAU Community

Recommended Posts

Hey Peeps

For May Meet Up we are going ice skating, This is going to be loads of fun and think I might even bring a pillow and some race tape..LOL

Date : 31st May (Saturday)

Time: 6:30pm

(We will have dinner first at club or somewhere on Hoxton road then go ice skating) :)

Meet Point : Bunnings Crossroads, Casula

Cnr Campbelltown Rd & Camden Valley Wy, Casula, 2170

post-8051-1207274747_thumb.png

Destination : Liverpool Catholic Club Ice Rink

Cnr Joadja & Hoxton Park Roads

Liverpool West

http://www.liverpoolcatholic.com.au/

http://www.lccfss.com.au/timetable.html

Hope to see you there!! :P

Link to comment
https://www.sau.com.au/forums/topic/201335-southerncampbelltown-meet-up/
Share on other sites

  • Replies 607
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I rekon Jeff and Dave would be up for it.

Someone find Micheal and get him along too (jeff :P )

Phill you still around here or has he been arrested now?? (jeff you know?)

Polak I remember you asking about a local meet up?

Ill bring the GTR out for a drive.

Edited by Risking

hey

im in wetherill park

but dont mind a cruise to campbelltown for a SAU meetup.

always love to see other skylines up close and personal.

keep this thread goin.

cheers,

Shane

Awesome guys :(

Sounds like we will have a good turn out already!! :(

I just remembered I'm busy the Friday of the long weekend so that's out for me :D

So post up what day's would suit you??

Saturday night

Sunday night cause Monday is the public holiday...

:blink: (I like this emcon lol)

bunnings is good, thats where i live lol

phil has sold his line off, he is in the wrong job for attracting the wrong sort of attention lol. i might get him a lift out to say hi tho.

dave is in japan with richard.. and his car is smashed lol

i will give michael a ring.

so thats a fair few people anyway. let me know a date and i can get a few more. ive had a requst for a sunday?

Yep, Saturday or Sunday night would be good.

Usually there is higher police activity on the roads on long weekends isn't there?

But if we ain't doing anything stupid we shouldn't have anything to worry about. Whats the agenda for the night? Just meet?

Are we gonna take a cruise somewhere?

Some one post a date, time, location etc just to make it clear for everyone please.

yea oprtos sounds good, kfc is there where bunnings is too.

btw i cant find any boost.. perhaps ive dropped a turbo. anyway i wont be in for anything serious like back when we were young and stupid. it will be trundle hi trundle eat trundle home

but and yet also... house might be empty so we could come back and play pool




  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...