Jump to content
SAU Community

What Turbo For 250+rwkw

r33madd

By r33madd,
in Engines & Forced Induction

 Share

Recommended Posts

r33madd Community Regular

r33madd

Posted
Posted

Hey all this year is time for project 250rwkw.

at the moment im sitting at 201.3rwkw with factory turbo.

so whats a good turbo upgrade and what other parts will i need to get my goal.

Currently my mods are

HKS Hiper Turbo back exhaust and HKS muffler

HKS super flow pod filter @ CAI

HKS EVC 5 boost controller @ 12psi

Apexi SAFC-II

Greddy Type R blow off valve

Autobarn88 600x300x76 intercooler

Sard Fuel pressure reg

Walbro 500hp Fuel pump

NGK Iridum Spark plugs @ .8mm

Splitfire Coils

Nismo G-Attack suspension

Link to comment
https://www.sau.com.au/forums/topic/201575-what-turbo-for-250rwkw/
Share on other sites
mesmerized Mentor

mesmerized

Posted
Posted (edited)

http://www.skylinesaustralia.com/forums/Rb...hl=dyno+results

but i dare say gtrs is the best bet if you're not on too much of a budget otherwise

http://www.skylinesaustralia.com/forums/Ni...et-t200277.html or a high flow

yes, if you want to get any benefit of a gtrs you need to upgrade your ecu, injectors etc

o and ibtl, it's been covered so many times.

Edited by into oblivion
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...