Jump to content
SAU Community

R33 S2 Highflowed Turbo

rinmak
 Share

Recommended Posts

rinmak Proficient

rinmak

Posted
Posted (edited)

Hey guys,

I have a highflowed turbo for sale that came off a stagea I bought recently. The turbo would suit a rebuild as there is some noticeable movement back and forth on the shaft and also side to side. The compressor housing also shows the slighest signs of being touched by the compressor wheel on occasion. The turbo did not make any noise before it came off and had a slight amount of oil left in the cooler pipes.

I have no receipts for the work as it was done by previous owners but I will get pics of the front/rear wheels and its quite obvious that it has been highflowed as they are massive.

Still yet to get a quote from a turbo shop to rebuild this but I would expect around the $400-$500 mark.

Done a search here and these highflows seem to go for about 1300 bucks secondhand so im going to ask $600 for my one as is. Will eventually get a quote on rebuild and may even have this done then sell as a new turbo but I thought I would post it up and see if anyone else wants to take it as is.

Located in Perth but should be ok to post.

Regards,

Ryan

post-18921-1200432660_thumb.jpg

post-18921-1200432714_thumb.jpg

post-18921-1200432729_thumb.jpg

Edited by rinmak
Link to comment
https://www.sau.com.au/forums/topic/201581-r33-s2-highflowed-turbo/
Share on other sites
stolen_s15 Mentor

stolen_s15

Posted
Posted

I'm interested, but your dreaming if you think people will pay $600 for a turbo that needs a rebuild.

Also is it ballbearing or journal? Who did the original work? Any dyno sheets?

rinmak Proficient

rinmak

Posted
  • Author
Posted (edited)

Fair enough. I wasnt very sure on the price so im open to offers. Feel free to PM me with one. Il also get a quote on the rebuild and at the same time hopefully get some specs. Way I saw it was that people pay 1500 bucks to get their turbo's highflowed, and if my assumptions are correct then this turbo will only need about 400-500 worth of work done to get it rebuilt and working properly as a highflow...so its basically a new highflow for 1k give or take.

Anyway, il get some pics and a quote in the next few days hopefully.

Oh and sorry no specs or dyno sheets. Ive had the car 2 weeks and only drove it half a k before a cooler pipe fell of and subsequently got run over =/.

Cheers guys.

Edited by rinmak
rinmak Proficient

rinmak

Posted
  • Author
Posted

Ok guys I spoke to the turbo place today and they told me the following:

- Definitely a high flow (duh)

- Capable of about 450hp

- Scoring on the compressor housing is easily tidied up.

- Compressor wheel will need replacement as one of the fins is slightly bent ($120 for new wheel)

- To expect about $800 all up for a rebuild inc parts and labour....and it was a worst case scenario sort of quote.

So in light of this the new price for the turbo is 300 ono

rinmak Proficient

rinmak

Posted
  • Author
Posted (edited)

Pm me your post code mate

Il see if my local PO is willing to ship it and how much etc and make a decision from there!

Edit: Post code = zip code

Edited by rinmak
  • 2 weeks later...
  • 1 month later...
Fero Collaborator

Fero

Posted
Posted

turbo is off a series 1 or 2 skyline or equivelent , actuator though is defenently off a series 1 skyline which leads me to believe its a series 1 turbo. rear wheel is defenently bigger and front i think is noticably different like mine with room to go bigger still. rear whwwl is same size as mine. does it have a rear steel for sure???? also core of turbo has noticable blemish marks in the metal which is a sign or uneven heat on the core. as you already know turbos get very hot so try get some close up shots to inspect for cracksin the casting. Really though for 100 dollars i would just buy it any way and take my chances b4 somebody else snaps it up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...