Jump to content
SAU Community

Recommended Posts

Great turn out today, over 40 cars in 6 hours made it onto the dyno. Well done to Mark and the team those guys were flat out all day. And great bbq too thanks ladies.

Well done everybody :P

Sadly my taxi couldn't make the dyno, even though I changed the fule pump and fixed the boost controller (OK bard did all the work and I watched :) thanks mate) it was still pinging over 5k - need to get the PFC in and see if it is just a tune or something else.

Pezhead, your 4wd is rooted - do you have a warning light, or does it just not work?

  • Replies 327
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Oh, and watching Josh get 301rwkw in his cammed VX SS makes me want an LS1 again....

;)

Yeah 301's ok......the winner was 365 :)

Hey folks great to see such a good turn out. For those that wondered why mine came back off the rollers before a run my front clutch pack is stuffed so I didn't want to do it any more damage. Geez out comes the VISA card again!

At least this confirmed it before I did any more damage out at power cruise. I hate it when my toy is broken :P

Glad to see so many tough machines today.

Very nice to see your car, as i said before, its just mint clean!

Shame about the clutch pack but thats cars :)

How was powercruise?

Yeah 301's ok......the winner was 365 :P

Very nice to see your car, as i said before, its just mint clean!

Shame about the clutch pack but thats cars :)

How was powercruise?

OoOO What made 365kw Steveo?? Was that the highest reading of the day?

RB GUN was the winner, with 365rwkw, packed in an r32 gtst

Although GTRsean did very well with 322 ALL wheel kw, shame we didnt get him to pop the fuse and get an rwd mode run in

RB GUN was the winner, with 365rwkw, packed in an r32 gtst

Although GTRsean did very well with 322 ALL wheel kw, shame we didnt get him to pop the fuse and get an rwd mode run in

I think you should check your sheet again.. someone hit a lot higher than that :P

I think you should check your sheet again.. someone hit a lot higher than that :P
lol true apparently there was a 600kw boat

Oops yeah, sorry there was a magic run from a boat that no one saw :)

aye n1 gtr........ was my 169.2rwkw the best for standard turbo @ 10psi for r32 gt-st???

When you left it was, but then Evan pulled a 181.1 on a peak of 20psi towards the end of the day

Oops yeah, sorry there was a magic run from a boat that no one saw :P

When you left it was, but then Evan pulled a 181.1 on a peak of 20psi towards the end of the day

wow......that was brave of him

wow......that was brave of him

Thats what i thought but it was only a peak of 20, most was around 15psi i think (saw a lot of readouts today, pretty sure the one im thinking of was his)

Good to meet a few ppl today face to face.. chris, burnsie etc.. had a really good day guys and

glad i made it on the rollers :P here my in car vid..

*ps* its not the tool, is the user :)

Liz owes me 20c :)

you owes us an apologize for lying :)

my pic for the day.

haha.. my quote of the day ;)

Oops yeah, sorry there was a magic run from a boat that no one saw :P

When you left it was, but then Evan pulled a 181.1 on a peak of 20psi towards the end of the day

thaTS MASSIVE WAS THAT STANDARD TURBO??? when are official numbers being posted??




  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...