Jump to content
SAU Community

Recommended Posts

Look I hate vee sixes as much as the next bloke, but there is a little more to it than just saying they are not perfectly balanced. It depends on their vee angle. Ever wonder why people produce 60 degree angled vee sixes?

i'm no engine engineer :banana:, but from what I gather there is no way to balance a V6 without using balance shafts.

http://en.wikipedia.org/wiki/Engine_balance

Have a look down the bottom for the lists of engines with inherent advantages and disadvantages of balance.

but as I was trying to say, balance is only part of the problem. Infact it is compactness which has pushed inline engines out of the mainstream. If you look back through time you will find massive inline engines (i've heard of an inline 16 engine) however as cars have become more and more compact these engines just can't work. That appears to also occur in 'performance' cars now too, where the balance of the engine position is more important than the some aspects of the power output.

  • Replies 63
  • Created
  • Last Reply

Top Posters In This Topic

well this is all true. but ultimately the length of a straight 6 leads means

harmoc problems (balancer and flywheel have to be right)

need for a really strong cranks (nice of nissan to give us a forged one standard)

spun bearings

poor packaging in the car

front heavy balance

they are dead. just like the inline 8 is dead too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...