Jump to content
SAU Community

Recommended Posts

Hey all,

Went to calder last friday for the 1st time and and ran my car a few times, was wondering what sort of times other similiar cars was getting as i was going up against 11 sec cars!

My car and Mods:

1993 R33 Gts-t (Auto)

Performance mods:

Apexi N1 catback Exhuast

R34 Side mount cooler

running 9 Psi

Tyres: 17 inch rims with 245 continental tyres (about 60% thread) 22 PSI

and everything else is pretty much stock. Not tuned or anything like that.

My best time was:

14.29 @ 157 km/h

most my times was between 14.3 and 14.6 - i had about 11 runs.

I found that the car would launch hard but then die in the last 100 meters :D

i would be very happy with that time.

our skylines up north just cant seem to push the same times. different track and maybe the prep will probably be part of the reason.

what 60ft time?

hmmm really? the weather could also play a part i guess....on friday (when i went) it wasnt too bad, track temp was about 24 degrees..

60ft time was: 2.11

660' - 9.12 @ 125 km/h

That's a good time.

Are you planning to go quicker?

ye id love to break into the 13 seconds... and then i will be happy.

My car is a daily driver, ive had it for about 5 years and i've done 110,000 km's on it since ive got it...

I rekon maybe with a FMIC, high flow cat + dump pipe i could improve the top end a bit and maybe break into the high 13's!

But at the same time, as it is now, its great for day to day street driving / over taking and quicker off the line than more modified / tuned manual R33's of some of my mates and i don't know if i want to lose that to gain a few milliseconds on the drag strip!

What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

60ft time was 2.11

thanks for the tip! ye i'm def going to invest in making the exhaust to turbo back me thinks!

Justjap have a nice deal going for you:

http://www.skylinesaustralia.com/forums/JJ...RB-t204414.html

So much cheaper than I first thought, wouldn't take more than an hours labour if it is a straight fit to your existing cat-back exhaust so you should be able to have it fitted for about $500 all up.

is it losing traction on launch?

being auto and stockish, I don't think it would.

anyway.

to get something like a 13.9 (in to the 13's as you're said).. get the exhaust finished (dump pipe and front pipe in one and a new large cat).

then get an SAFC and have it tuned.

Even the blue screen SAFC would get you a good increase in power, especially in the upper end.

the Blue screen ones would be below $300 now for sure.

dump/front pipe in one can be picked up for about $200 from a number of places brand new.

SAFC tune will probably set you back about $200.

all of that easily under $1K.

should push power to near 190rwkw.

should net you 13.xx

if you are losing traction on launch, then look in to tyres too.

I would also race with 16's instead of 17's.

I dare say that your 17's with tyres would weigh more than the stockers which weigh 16kg with tyres.

EDIT - don't replace the R34 SMIC with a FMIC.

you will lose the response that you love at the moment.

it is more than up to the task.

If the R34 SMIC doesn't have any ducting to it, I would look in to making one for it.

Water spray is another option but probably not needed.

Edited by GTST
What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

his current mph is more like 97

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean it's a bit late to say "This won't have any tangible effect and it is not worth spending more than about three seconds on it, please just enjoy the car" But I said it anyway. Does the pod actually get any airflow in that position behind a bumper like that?
    • Hey guys - apologies for digging this up. Has this website been shutdown or is the outage temporary?
    • So, went shopping at Just Jap for things that might work for the intake  After some trial fitting there I ended up with a 3" x 45° silicone bend, a 3" x 300mm alloy straight, and a humped joiner, some minor trimming will be required to shorten some of the stuff, but nothing that is beyond my "ham fisted" skills The guy at Just Jap was most helpful as we had all sorts of joiners,  bends and stuff out trial fitting  Laying it out above the stuff in there it seems everything will fit nicely, and looking at it, it is probably the way I should have been looking at doing it from the beginning, probably..... In the end it is a front bar off job anyway to remove the original stuff behind the front bar that is taking up the required realestate needed, so maybe a Thursday or Friday job And because I'm a hopeless consumer, I grabbed some new steel wheel nuts, the current ones are a spline drive type with a "security" socket, that somehow someone keeps misplacing, the new ones are a basic black steel 17mm hex socket In other news: I just did my "final" tax return, I am now officially a old retired veteran pensioner, and I'm milking the system for all it's worth,  life is good
    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
×
×
  • Create New...