Jump to content
SAU Community

Recommended Posts

hey guys,

bought a brand new xforce highflow cat off Ryan1600 and put it on the car tonight.

With the new cat on, even with the gaskets, in the middle of the ovals on either side that join to the next part of the exhaust ( the part furthest away from the bolts) I can put my hand under there and feel some of the warm exhaust gases blowing out in the crack.

Just to make it clear... so if the top and bottem of this oval are where the bolts are, the part that I can feel gases is ... ---> () <---

Is this acceptable or does it have to be completly sealed? and if so, wot is the best way?

And I tightened the bolts up hard enough to squish the bit of the gasket around them, but not in the middle.

1 other thing, my old gaskets appeared to be larger then the ones that came with the xforce... should those maybe go back on?

appreciate the help :)

Adam

Link to comment
https://www.sau.com.au/forums/topic/205808-question-about-exhausts-and-joins/
Share on other sites

The flange on the existing pipes has probably warped a bit. You can get special high temperature sealant (like putty) that you can coat the gasket with. That should help create a proper seal at the flange joints.

Thanks guys, appreciate the help.

Can I drive the car around for the day as it is?

is it possible for me to put two gaskets on? ie, the old + new one? or is that a bad idea? because by the looks of the old 1, with that combined with the new 1 it should be a good fit.

just use that exhaust gasket goo stuff. it's only about $10 a tube. put it on the flanges and use a gasket as you did, and hopefully it will seal. if it doesnt, you'll need to find which face is warped and get it machined flat. well not even really machined.... you could prob do it yourself with a grinder and a steady hand.

Edited by Munkyb0y

I will go out and get a tube of that stuff ( sounds like it could come in handy) but I just chucked on the old and the new gaskets together and it now appears to be fine :) I may still put some stuff on it just to be safe.

Thanks for the help guys ;)

You'd be better off with two gaskets. Goo will take weeks to get it hard enough to be heat resistant. Usually melts or burns out - and its messy

If you machined it flat you shouldnt even need a gasket as the materials are the same and will be running at the same temp

If you pull it off yourself it would cost less than the goo to machine

The stuff u need to buy is CRC Maniseal Exhaust Cement!

u use this stuff on both sides of exhaust gaskets and as the first time the pipes get some heat in them this stuff will set and stop all those unwanted leaks!

you can purchase it from any auto place eg. repco, bursons, supercheat, etc

Appreciate the help guys.

You know, I gave the car a bit of a flog today, only for a couple of minutes, now I don't know if I have started to become used to the slight lack of power or if the power has gotten back up to what it was somehow.

you know that sensor that plugs into the cat? wot does that do? does it tell the car how much approprate flow it should have? I don't know, it just seemed to have a good strong burble session down this hill, then after that the power didn't seem to be as laggy and it feels abit more torquier from then on.

is this possible?

the other thing I am curious about. these cats flow at 570cfm or some unit of measurement. how much flow does a straight 3" pipe provide?

Adam

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...