Jump to content
SAU Community

Recommended Posts

97 87000km Series 2 RB25DET Gearbox and conversion parts, flywheel, 1/2 Drive Shaft ect $2000ono or Just Box $1500

Series II Interior in good condition (Seats, Door Trims) $350

R33 GTS-T S1 Non-ABS LSD $200

3" Front / Dump Pipe $150

Drivers side window Regulator $100

Complete Passanger side door complete less trim with small scrape. $200

Steering wheel- Series 2 Leather. Airbag not included Very good wheel $50

Some suspension parts.

Parts are in, Brisbane

post-47634-1205850715_thumb.jpg

Edited by Brokenz

Power Fc sold for $1250. I thought $1250 would be normal price for a used PowerFc as they are selling new at the moment on Ebay for $1540

Splitfire Coils Sold for $300

Decent priced pfc for both seller and buyer. PFCs should be coming down in price again, as they are once again available new. Limited stocks at the moment, but should increase again soon. Hopefully will have them available for brand new around the $900 mark again soon. Those were the days.

  • 2 weeks later...
97 87000 Series 2 Engine with Std Turbo and loom $1650 (155-160 Compression, Splitfire Sparkplugs)

(Sold to Paul @ Option 1)

97 87000km Series 2 RB25DET Gearbox and front 1/2 of tailshaft if required $1500

Series 2 Nismo Copy white cluster with blue backlights 180kph 87000km $200

Series II Interior in good condition (Seats, Door Trims) $350

White Series 2 Bootlid and spoiler $150, White Series 2 Doors Less Trims, Regulators and Glass $250

Also have series 1 front and rear bar, rear windscreen, S2 ABS LSD Diff, and 1/4 glass and most other parts except for panels

Parts are in, Brisbane

u got pics of the cluster ?

  • 2 weeks later...

Mate,

Any photos of the front pipe?

97 87000km Series 2 RB25DET Gearbox and conversion parts, flywheel, Std Clutch, 1/2 Drive Shaft ect $2000ono or Just Box $1500FIRM

Series 2 Nismo Copy white cluster with blue backlights 180kph 87000km $200

Series II Interior in good condition (Seats, Door Trims) $350

R33 GTS-T S1 Non-ABS LSD $200

3" Front / Dump Pipe $150

Drivers side window Regulator $100

Complete Passanger side door complete less trim with small scrape. $200

Steering wheel- Series 2 Leather with airbag missing. Very good wheel $100

Some suspension parts.

Parts are in, Brisbane

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...