Jump to content
SAU Community

Recommended Posts

Sorry, but you have missed the point of having a baffled sump - The point of the baffles isn't to keep your oil cooler, but rather to prevent oil starvation under hard cornering/load, which is particularly common at the track.

Ideally, anyone building an engine should be at a minimum fitting sump baffles, a good quality oil cooler, and an upper oil gallery restrictor.

If hes doing that kind of cornering and high revs on the street his car should be crushed and his license taken away for life... having said that i highly doubt this person was.. this is my point. unless hes on the track a think upgrading a sump is a waste of time.

Link to comment
https://www.sau.com.au/forums/topic/206613-r33-gtr/page/2/#findComment-3657029
Share on other sites

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Ok, its got forged pistons, strip,clean and inspect block, machine block, test and machine crank, resize conrods and rebush, ACl race bearings and mains, N1 oil pump 22000km on the motor blueprinted bottom end it had fresh oil 5w.30 castrol

the car is just a street car, it was bouncing off the limiter abit. but when it happened i wasnt driving and i wasnt in the car. my 'MATE' the car was warm but when he got in and took off straight away and hit the limiter in first and 2 min later it when he came back it was F*C*ED

also the car had not been tuned so it was running rich as on about 20psi

Edited by tom9999
Link to comment
https://www.sau.com.au/forums/topic/206613-r33-gtr/page/2/#findComment-3657627
Share on other sites

Ok, its got forged pistons, strip,clean and inspect block, machine block, test and machine crank, resize conrods and rebush, ACl race bearings and mains, N1 oil pump 22000km on the motor blueprinted bottom end it had fresh oil 5w.30 castrol

the car is just a street car, it was bouncing off the limiter abit. but when it happened i wasnt driving and i wasnt in the car. my 'MATE' the car was warm but when he got in and took off straight away and hit the limiter in first and 2 min later it when he came back it was F*C*ED

also the car had not been tuned so it was running rich as on about 20psi

Do not drive their cars. Reciprocity will be working to your advantage if you dont drive their cars. Seriously :)

Sounds like there was a lot of limiter involved, first place to start is the oil pump

Before buying new parts though, strip the motor down and see whats ok and whats not, then spend the money :P

Link to comment
https://www.sau.com.au/forums/topic/206613-r33-gtr/page/2/#findComment-3658710
Share on other sites

it was bouncing off the limiter abit. but when it happened i wasnt driving and i wasnt in the car. my 'MATE' the car was warm but when he got in and took off straight away and hit the limiter in first and 2 min later it when he came back it was F*C*ED

Your mate wasn't getting enthusiastic with chucking nuts by any chance was he?

This can cause the same sort of oil starvation issues that track cars would come up against.

High rpm would of filled the head with oil if no restrictor was in place.

IIRC some ppl have mentioned recently some N1 oil pump failures recently...

Sump baffles + oil gallery restrictor + aftermarket oil pump should be your new friends IMHO

Link to comment
https://www.sau.com.au/forums/topic/206613-r33-gtr/page/2/#findComment-3660933
Share on other sites

everyone assumes its the oil pump! A lot of times it is, particularly on RBs, however, I've seen more engines spin bearings due to detonation like Proengines suggested! If the cars had a fresh build and has 23000ks on it and has been pinging the whole time due to a bad tune or even crappy fuel something has to give! In this case forged pistons aren't as likely to crack a land and the shock of detonation will overtime hammer the bearing flat and then the crank may pick it up(most likely at the time between the violent resonance when launching of the limiter when driving your friends GTR like you stole it) And a good engine builder will be able to confirm if in fact it was pinging just by looking at the bores.

Hope you get her fixed.

Link to comment
https://www.sau.com.au/forums/topic/206613-r33-gtr/page/2/#findComment-3668773
Share on other sites

ok so the motor has been pulled apart and by the looks of things it had been built incorrectly and they have cut corners!!! it was the third bearing in.

its now getting

new H beam rods

new forged pistons

blueprinted bottom end

MLS gasket

and etc

Does anyone know how much boost i can run safely

Link to comment
https://www.sau.com.au/forums/topic/206613-r33-gtr/page/2/#findComment-3683258
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...