Jump to content
SAU Community

Motorplex meet.

Guest Rhino

By Guest Rhino,
in Western Australia

 Share

Recommended Posts

  • Replies 233
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

rob77 Veteran

rob77

Posted
Posted

Well I didnt have much luck. With the warmer weather and the stock intercooler I couldnt run 0.8bar of boost effectively. My fastest run of the day netted me the same result from my last day at the drags another 14.8 with the boost turned down to 0.6bar. Time to browse the Trust catalogue for a better intercooler and some sort of new engine management I think. The car was launching much better with the lock kit though, its a bit annoying though as I know the car is quicker because at night when its much colder at 0.8bar the car pulls strongly to 6500rpm, today with 0.8bar I had to keep shifting between 5500 and 6000rpm because the power was tailing off... damn heat! Either that or my car's a lemon :(

Rob

Gradenko Mentor

Gradenko

Posted
Posted
Originally posted by MrSnrub

Also what dyno did you get 253rwhp on? :D  

I know what you're thinking, and no, its not Myaree Dyno :P

Got it tuned at Barrys Dyno.

adam 32, no need to prove anything, the terminal speed shows the true potential of the car. Besides, 12psi will make you harder to catch at the next cruise :(

rob77, the factory tune on the r33 ecu is junk. Put fuel control at the top of your list, you won't be sorry.

rob77 Veteran

rob77

Posted
Posted

Yup, black r33 stock rims and body, nice 3.25" cat back system with the muffler on a angle and a tip big enough to stick your head in :( The only other mods are a blitz air filter element, apexi twin chamber bov (which I'm thinking of ditching cos I think its causing my problems), blitz dual sbc type s boost controller. I was hoping on at least a low 14, possibly a high 13, but the gremlins re-appeared. My terminal speed was 96.05mph or 154.57kmh at 0.6bar, so with a stronger clutch and harder launch, I dont see why I cant run a low 14 at least.

Rob

rob77 Veteran

rob77

Posted
Posted

Adam32 read my post, I run 0.8bar of boost and it's fine at night, the car pulls hard all the way to the 7200rpm limiter, but for some reason today be it heatsoak or something else is ****ed in the car, it was loosing power if I went past 5500rpm. I'm sure if I went out now and took it for a drive, it'd pull fine to 7200rpm. *shrug* beats me, everytime I go to the drags something ****s up.

Rob

Gradenko Mentor

Gradenko

Posted
Posted
Originally posted by rob77

[snip]

The only other mods are a blitz air filter element, ...

[snip]

So I take it the blitz element is in a stock unmodified airbox? Or have you hacked the airbox to include a cold air intake?

The stock airbox is an unbelievably huge restriction in R33 GTS25ts, the GTR design is much better.

Guest Rhino

Guest Rhino

Posted
Posted

Only did 6 runs as I was stupidly consistant, here they are in order:

13.989 @ 167.24

13.112 @ 163.47

13.038 @ 168.41

13.080 @ 164.95

13.073 @ 161.64

13.093 @ 168.41

As Troy said today there was a bee's dick to a 12 for me today, I wont be going back until I get a new clutch and make sure I dont have 50L of fuel onboard like I did today...........and maybe flogg some race rubber off Ken???:( pretty please??

Cheers.

ix9 Grand Master

ix9

Posted
Posted

Ben: Yeah man, i think you were too busy liftin the bonnet of your beast in the pit lanes to realise i was runnin around...

I was wearing the dark blue polo shirt with www.hyperwa.com on the back..

Also guys, there's an image gallery up at http://hyperwa.com/gallery/dragwars02_s9/ so you guys can see your ride's....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...