Jump to content
SAU Community

Recommended Posts

that looks good, should be nice and torquey. It good to see the more extreme conversions still happening.

I doubt there are going to be any turbos on the side of that, by looking and the room just some simple headers look to be a stretch, although if they could make the manifold come to the front of the car, you probably could stick one nice big single in front of the engine.

What car is this out of??

Edited by R34GTFOUR

The VK56 has a pretty bullet proof bottom end.

These things are out of nissan Titans that weigh between 2200kgs to 2400kg's or so and 15.4 sec 1/4 miles out of the lightweight? 2,200kg ones have been done stock. not bad for a full size truck with a 5spd auto-gearbox. People get them into 12's with a small shot of gas . lose 800kgs or so and how fast would you go? :D

the day my engine is knackered im gonna steal dads 400hp+ 5.7 v8 out his ss and put it in my line, the guy who tunes dads ss has a r33 with 5.7 v8 and he is so quick round barbagello,

That would be the Street Force R33 Skyline, that conversion was done years ago, sounds nice as though.

And yeah that car above with the R34 GTR front end on it would be the twin turbo R34 coupe that is bashing around the Drift Australia circuits.

Also in regards to the VK56 conversion, I've seen a couple of people bash around with the VH45DE motor, which would be the motor series before the VK (which are also quad cam alloy V8's that are also a shit load cheaper to buy) in a couple of nissan platforms.

The main issue with the VH45DE was the height issue, with most people resorting to cutting the bonnet open to fit it in. And also finding that a manual gearbox bell housing would have to be fabricated to fit up a manual box. I believe there is a R33 with this conversion floating around in the Naturally Aspirated section with an auto box. Think it has a blower as well.

There are only two V8's that I would bother putting into a skyline and thats the 1UZFE (4.0l alloy quad cam V8) which I wouldnt bother unless there was some sort of forced induction hanging off the side of it....... or the LS1 which are a tough motor as it is, TON'S of aftermarket support like off the shelf turbo kits and have a variety of strong manual gearbox's to bolt up to it. Not to say also that replacement motors are dead cheap.

  • 3 years later...

This engine is also out of a Nissan ARMADA 04-05 5.6L V8 DOHC

its a 4WD or SUV wateva you want to call it probley weighs a fair bit aswell

claimed 317Hp 385 LB-FT Torque.

Edited by HYBRID VL

i have heard alot of good things about the L67 V6 SC like its the strongest engine holden has ever built and stuff like that Guys running 10's with a twin turbo setup on standard internals also heard they are very hard to source and alot are fake standard V6 with a SC on top.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...