Jump to content
SAU Community

R33 Gtst Flat Spot

bean962

By bean962,
in Engines & Forced Induction

 Share

Recommended Posts

bean962 Newbie

bean962

Posted
Posted

Hello all.

I am so angry I cant find the reason for this so I'm offering a reasonable reward for the soloutiion.

I have an R33 GTS-T and a massive flat spot at 4500 rpm until 6000.

I have replaced or changed:-

ECU

New Coil packs (for splitfires)

New Iridium plugs

AFM

CAS

Ignition amplifier

Knock sensors

The diagnostics say the ignition retards to about 5Deg at 4500 rpm and then goes back to normal 15/17 deg at 6000. Obviously during this period its running rich, so any ideas?

Link to comment
https://www.sau.com.au/forums/topic/207039-r33-gtst-flat-spot/
Share on other sites
bean962 Newbie

bean962

Posted
  • Author
Posted

Sorry, I've only had a skyline for a week and I just thought the Aussie club would offer better advise than our UK forums.

The car is completely stock except big bore front pipe and de-cat pipe.

Is the problem likley to be the boost solenoid?

Regards

sik14 Enthusiast

sik14

Posted
Posted
Sorry, I've only had a skyline for a week and I just thought the Aussie club would offer better advise than our UK forums.

The car is completely stock except big bore front pipe and de-cat pipe.

Is the problem likley to be the boost solenoid?

Regards

does it just sound like its missfiring then clears its throat and pulls fine through the rest of the rev range?

bean962 Newbie

bean962

Posted
  • Author
Posted

Thanks for all your constructive replys

Yes it stutters at 4500 and then at 6000 clears its throat and bang....BHP up to 260

I've replaced the o/e ECU with a standard unit

The plugs are greddy

Standard boost

Ignition retards to 4 or 5 deg at 4500 and then goes back to 16/17 at 6000

The voltage on the AFM goes off scale at this RPM but the turbo pipes have been checked and no leaks found.

I'm buggered......

R33silverS2 Mentor

R33silverS2

Posted
Posted
I appreciate I can change the ECU to a Power FC but Nissan didn't design the car to run like this so fitting a power FC will only mask the problem and no diagnose the reason.

it won't 'mask' the problem... it will FIX the problem. The problem is your ecu - the standard nissan ecu is the problem. as covered many times it has factory protection wirtten into it which retards the timing and richens the mixtures when airflow exceedes a certain amount. you obvisoulsy have higher boost than stock to make 260hp, what boost is the car actually running? A power fc is a full replacement engine ecu not a piggy back so thier is no 'masking' so to speak.

edit: do you have a boost gauge or are you just using the standard one? stock should be 7psi and therefore your airflow metre should not be maxing out at this level.

mattymagoo22 Community Regular

mattymagoo22

Posted
Posted

Bean. Nissan designed the car to run exactly how it came off the production line. 3psi<4500 7>4500rpm, no big bore exhaust without a cat. The second you change the exhaust, boost,tubo, fuel pressure etc etc these are things that can potentially harm or in some cases destroy both the engine and the turbo. As mentioned before if boost is raised the cars ECU goes into R&R (richen up and retard timing) to prevent high cylinder temps and detonation which occur when outright power is sort after and none of the supporting systems are considered (AFRs, intake temps, injector duty cycle etc etc).

So to sum up, installing an aftermarket ECU or having a tune done is not masking the problem, it is simply getting the most from what you have SAFELY! the factory tune isn't designed for outright power, its a compromise between power, economy and longevity and by running the way it does its saying something isn't right I got to save myself and so the extra fuel goes in and the timing gets pulled out of it.

Cheers.

SLYDA Community Regular

SLYDA

Posted
Posted

AFM should read up to 5V i believe before maxing out (correct me if wrong) it may be 5.2V - Get a Power FC and a Z32 AFM .. or set ur boost 2 10PSI and dont touch it.. my series had the same problem for about 2 years... try running 14 or 15PSI and it seems fast up to 4500RPM then just died.. Found the car was far faster on 10PSI, now i have a HKS GT3037 Pro S on it.. and at 10PSI with a POWER FC.. all i can say is.. i wish i had of done this 2 years ago..

What you are talking about is called the FACTORY BOOST CUT.

Every member on this forum that has even slightly modified there skyline and upped the boost has encountered this problem

Yo-Yo Grand Master

Yo-Yo

Posted
Posted

As others have already said, it's your factory computer protecting the car from blowing itself up.

Any aftermarket replacement ECU will make full use of your modifications, piggyback air/fuel controllers will do the same thing to an extent, but nowhere near the level of a stand-alone engine management systems.

Most of the guys mention Power FC because it's arguably the most user friendly ECU, other brands are HKS, Trust/Greddy Emanage, Motec etc. just to name a few... all with various costs and pros and cons.

I have a Power FC in my r34 and never had a drama with it, I liked how it already had all the standard ECU maps like cold start and electrics eg. air con control, but let's you re-write the parameters of the factory ecu.

Any competent tuner can install these systems and effectively fix the problems you've been experiencing.

TTT Grand Master

TTT

Posted
Posted
I appreciate I can change the ECU to a Power FC but Nissan didn't design the car to run like this so fitting a power FC will only mask the problem and no diagnose the reason.

bahahaha...

but they designed the car keeping in mind that people would replace the front pipe and remove the Cat convertor all together right?

Brilliant.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...