Jump to content
SAU Community

Recommended Posts

Hello all.

I am so angry I cant find the reason for this so I'm offering a reasonable reward for the soloutiion.

I have an R33 GTS-T and a massive flat spot at 4500 rpm until 6000.

I have replaced or changed:-

ECU

New Coil packs (for splitfires)

New Iridium plugs

AFM

CAS

Ignition amplifier

Knock sensors

The diagnostics say the ignition retards to about 5Deg at 4500 rpm and then goes back to normal 15/17 deg at 6000. Obviously during this period its running rich, so any ideas?

Link to comment
https://www.sau.com.au/forums/topic/207039-r33-gtst-flat-spot/
Share on other sites

Sorry, I've only had a skyline for a week and I just thought the Aussie club would offer better advise than our UK forums.

The car is completely stock except big bore front pipe and de-cat pipe.

Is the problem likley to be the boost solenoid?

Regards

Sorry, I've only had a skyline for a week and I just thought the Aussie club would offer better advise than our UK forums.

The car is completely stock except big bore front pipe and de-cat pipe.

Is the problem likley to be the boost solenoid?

Regards

does it just sound like its missfiring then clears its throat and pulls fine through the rest of the rev range?

Thanks for all your constructive replys

Yes it stutters at 4500 and then at 6000 clears its throat and bang....BHP up to 260

I've replaced the o/e ECU with a standard unit

The plugs are greddy

Standard boost

Ignition retards to 4 or 5 deg at 4500 and then goes back to 16/17 at 6000

The voltage on the AFM goes off scale at this RPM but the turbo pipes have been checked and no leaks found.

I'm buggered......

I appreciate I can change the ECU to a Power FC but Nissan didn't design the car to run like this so fitting a power FC will only mask the problem and no diagnose the reason.

it won't 'mask' the problem... it will FIX the problem. The problem is your ecu - the standard nissan ecu is the problem. as covered many times it has factory protection wirtten into it which retards the timing and richens the mixtures when airflow exceedes a certain amount. you obvisoulsy have higher boost than stock to make 260hp, what boost is the car actually running? A power fc is a full replacement engine ecu not a piggy back so thier is no 'masking' so to speak.

edit: do you have a boost gauge or are you just using the standard one? stock should be 7psi and therefore your airflow metre should not be maxing out at this level.

Bean. Nissan designed the car to run exactly how it came off the production line. 3psi<4500 7>4500rpm, no big bore exhaust without a cat. The second you change the exhaust, boost,tubo, fuel pressure etc etc these are things that can potentially harm or in some cases destroy both the engine and the turbo. As mentioned before if boost is raised the cars ECU goes into R&R (richen up and retard timing) to prevent high cylinder temps and detonation which occur when outright power is sort after and none of the supporting systems are considered (AFRs, intake temps, injector duty cycle etc etc).

So to sum up, installing an aftermarket ECU or having a tune done is not masking the problem, it is simply getting the most from what you have SAFELY! the factory tune isn't designed for outright power, its a compromise between power, economy and longevity and by running the way it does its saying something isn't right I got to save myself and so the extra fuel goes in and the timing gets pulled out of it.

Cheers.

AFM should read up to 5V i believe before maxing out (correct me if wrong) it may be 5.2V - Get a Power FC and a Z32 AFM .. or set ur boost 2 10PSI and dont touch it.. my series had the same problem for about 2 years... try running 14 or 15PSI and it seems fast up to 4500RPM then just died.. Found the car was far faster on 10PSI, now i have a HKS GT3037 Pro S on it.. and at 10PSI with a POWER FC.. all i can say is.. i wish i had of done this 2 years ago..

What you are talking about is called the FACTORY BOOST CUT.

Every member on this forum that has even slightly modified there skyline and upped the boost has encountered this problem

As others have already said, it's your factory computer protecting the car from blowing itself up.

Any aftermarket replacement ECU will make full use of your modifications, piggyback air/fuel controllers will do the same thing to an extent, but nowhere near the level of a stand-alone engine management systems.

Most of the guys mention Power FC because it's arguably the most user friendly ECU, other brands are HKS, Trust/Greddy Emanage, Motec etc. just to name a few... all with various costs and pros and cons.

I have a Power FC in my r34 and never had a drama with it, I liked how it already had all the standard ECU maps like cold start and electrics eg. air con control, but let's you re-write the parameters of the factory ecu.

Any competent tuner can install these systems and effectively fix the problems you've been experiencing.

I appreciate I can change the ECU to a Power FC but Nissan didn't design the car to run like this so fitting a power FC will only mask the problem and no diagnose the reason.

bahahaha...

but they designed the car keeping in mind that people would replace the front pipe and remove the Cat convertor all together right?

Brilliant.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...