Jump to content
SAU Community

Recommended Posts

hey guys got a r33 with bad brake squeel,i got the rotors machined and bendix ultimate in there and they still squeel the guys at the shop reckons the pistons are getting stuck out and that i should try and bleed them then if they doesnt work i will have to overhaul the calipers, wat do you guys reakon my best option is????

Edited by bwebbie1
Link to comment
https://www.sau.com.au/forums/topic/207227-bad-brake-squeel/
Share on other sites

well most squeal can be cured with:

installing the factory anti squeal shims

using copper grease, or the special anti squeal paste

champhering the edges of the pads if not done from factory

re-bedding them in

but, I have a set of pads. Endless CC-R, and they squeal no matter what. Hot, Cold, New, Old with shims, without shims they are just a noisy pad. you shouldn't have that problem with ultimates though.

im having the same problem with mine only at real low speeds "just befor stoping" where can i get the factory anti squeal shims?? i remmeber the guy who was instaling my pads took them off and threw them away cuz the breaks were bighting while they were on...

iv tried everything appart from changing the brake pads which is what im going to do but i think will still not solve my problem.. so it could be that small peace of mettal "shims" that shoulda been there..

well most squeal can be cured with:

installing the factory anti squeal shims

using copper grease, or the special anti squeal paste

champhering the edges of the pads if not done from factory

re-bedding them in

but, I have a set of pads. Endless CC-R, and they squeal no matter what. Hot, Cold, New, Old with shims, without shims they are just a noisy pad. you shouldn't have that problem with ultimates though.

i have the same problem aswell same pads aswell still working on the problem sum people might not like this but i couldnt stand the "squeel" anymore so i took them out rubbed them on some smooth cement and they stopped for about a month now they only do it every now and then and only a bit aswell might save your ears for a bit only a quick fix but

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Try looking at Eibacb/H&R springs Thats what Gary sourced for mine.
    • Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • I have an R32 Fenix rad. It is good.
    • All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
×
×
  • Create New...