Jump to content
SAU Community

Recommended Posts

Hi all.

I got a R32 GTR with stockies, 8 inch 35/38mm offset (cant remember). I picked up a set of enkies from work, 17X9 with a 22 mm offset. Will these screw up my handling if I fit them?

I've talked to some so called experts about it and the replies have been very unprofessional. One place who specialises in big rims replied with "All offset is good mate". Err no its not, it messes up wheel alignment angles real bad, scrub radius and track go out the window when messing with offset.

Any knowledgable help if appreciated.

Link to comment
https://www.sau.com.au/forums/topic/207455-dont-fully-understand-wheel-offset/
Share on other sites

I keep forgetting, but I thought GTR's wheels were +30 offset? We'll just say that they're +38 offset on a 8" rim for now, moving to 9" +22mm offset wheels will make the wheels stick out an extra ~21mm from where it is now. An increase in track so I guess that's a good thing (I've got no idea on track work so please forgive me).

So the new wheels will be sticking out an extra ~21mm from what they are currently. You could need some guard rolling done.

Where/how do you measure offset?

Because I have heard abour 4 or 5 offsets on GTR R32 wheels.. and this is on quite official papers..

All rims should have their offsets and widths either printed or on a sticker on the wheel somewhere. Usually on the inside, but I've seen a few wheels which had the offsets printed on the lip.

You can always rely on Yahoo auctions to tell you the offsets of standard wheels, and give you a good idea of what a particular type of second-hand aftermarket Jap wheel may be too. http://search1.auctions.yahoo.co.jp/jp/sea...=0jp&acc=jp. For the record R32 GTR is 16x8 +30.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...