Jump to content
SAU Community

Recommended Posts

hey guys,

it feels like the usual feeling of power lost, few secs(slip light blinks a few times) and u get normal power after that. i don get this on 1st 2nd or 3rd.

yeah i know at this rate of power, i shouldnt be slipping at 4th gear.

most probally its the clutch. (yes, clutch is stock)

BUT can anyone tell me how the clutch is affecting the traction control??

i was driving around 100km/hr at 4th gear and the light started to pop up. at first i thought it was missfiring but i have already replace the spark plugs and coilpacks recently.

hey guys,

it feels like the usual feeling of power lost, few secs(slip light blinks a few times) and u get normal power after that. i don get this on 1st 2nd or 3rd.

yeah i know at this rate of power, i shouldnt be slipping at 4th gear.

most probally its the clutch. (yes, clutch is stock)

BUT can anyone tell me how the clutch is affecting the traction control??

i was driving around 100km/hr at 4th gear and the light started to pop up. at first i thought it was missfiring but i have already replace the spark plugs and coilpacks recently.

i explained it a few posts up.

if you want a real test of the clutch... turn the TCS off, put it in 3rd, dial up 7000 rpm and drop the clutch and floor it :)

*doesnt take responsibility for burnt ouit clutch and flywheel that will result

well i just put a exedy 3 puk clutch in my r34 gtt and my slip light still comes on only wen tc is on but wen u turn it off its fine a bit more fun as well like a few people hav said drive with tc off

Edited by fab34

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...