Jump to content
SAU Community

Recommended Posts

Guest Rhino

Us WA ppl are in the middle of organising a trip down to the Motorplex in the next couple of weeks and I was looking for advice on launch techniques for a R32 GTR.

I have dialed up 5,000rpm on the street and it bogs, whereas 6500rpm is pretty good in my opinion. What is a good launch rpm for a proper strip?

I want the GTR's first run session(not to mention mine) to be a good, fast and safe outing. I hope redline launches aren't going to to be the order of the day as I'd prefer not to rape my car to get a good time when a sensible approach will net a good result.

Fingers crossed for 12's.

Cheers,

Ryan.

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/
Share on other sites

  • 2 months later...

From memory there was a .30sec reduction in ET by increasing launch rpm from 5,500 - 7,000rpm, terminal speed went up by 4 - 6kph as well.

7,000 launches give a fair whack of wheel spin and spinning in 2nd was also common, depending on whether I got the shift to 2nd right.

I did 4 13.0xx sec passes in a row with my old clutch which was a factory item about half worn with a dodgy flywheel face. The MC day the Perth people had last Sunday was my first chance to flog the new clutch and it has proven to be pretty bloody good for a clutch that isn't any harsher or harder to drive than the factory unit.

The day at the drags was good, but no 12sec. passes just lost of 13.0's!! That was with the old clutch slipping a bit and 50L of fuel on board. Next time 1/4 tank of fuel and I'll have a 12sec timeslip in my pocket.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69798
Share on other sites

heres ulas results

1st run...

5 grand dump, as i usually do on the street.

60 foot - 2.024

ET - 13.129

MPH - 106.52

2nd run...

i thought that i was wheelspinning too much off the line so i took off at a 4 grand dump (wrong thing to do!)

reaction time

60 foot - 2.310

ET - 13.903

MPH - 104.61

3rd run...

on this run, we all decided that i just launch at a 7 grand dump. the car rocketed!

60 foot - 1.881

ET - 12.776

MPH - 107.41

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69803
Share on other sites

ok cool... have u had it tuned?

ula had his tuned at the dyno day we had not long ago... cant remember the mods he has but its nothing outrageous but i remember he was getting 210rwkw or around 275rwhp.

hes running the stock GTR rims and not sure on the tyres

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69818
Share on other sites

heya Rhino... my rims are standard with crappy 225 rubber on them. clutch has also been upgraded but mines only a cat back exhaust. our theory was that you have to get the rear wheels to spin so the computer picks it up and then moves power to the front wheels which gets you the better take off, hence the 7000 dump. i wasn't game to try the rev limiter dump (only on gran turismo 3 hehe :) ) i know that my times wouldnt improve unless i had better and wider rubber. hope you get a good time!

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69834
Share on other sites

Hey Guys,

Use the rev limiter. Thats what it's there for!

The best way to get consistent launching is to take off the same

every time.Hold the revs up around 5-6000 then when the first

amber comes on flatten it and watch for the green.The trick is not

to sidestep the clutch(which will create problems-trust me) but to

ease it off with a little bit of slip.You must hold the car on the line

with the handbrake(or a line locker)to take up the slack in the

driveline.I have smashed std driveshafts, diff output shafts,3 gearboxes, & recently an HKS driveshaft!!! It just takes practice.

You shouldn't start breaking things until you pass 300rwkw, so if

your GTR is stock or mild give it heaps.Biggest problem is tyres.

Old, hard road tyres will not hook up.Borrow some sticky ones,

do big burnouts, experiment with tyre pressures,etc.

Drag racing GTRs is great fun.

I took out my R34 which only has exhaust & apexi power FC and

ran 12.1 @ 115mph! Don't over rev it. If your car is not making power over 7000rpm change gears earlier - it will run faster.

Have fun.

P.S. I have a mate over there with a GTR torana.Runs mid nines!!!

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69851
Share on other sites

Yep,

I do drive my R34 that hard.It's the only way to get it off the line

properly without bogging.Check out the Jap guys.You always hear

them popping on the rev limiter before they launch.:burnout:

Go hard or Go home.With the R33(OS 3 Litre engine) I sit on

9000 rpm for at least 5 seconds before launch to build up the boost.Any 4WD with a small capacity turbo engine needs revs to

launch hard.They don't have much bottom end torque, so if you

come off the clutch too early you bog the engine, lose torque, &

lose time. It is much easier to launch a V8 because they have so much torque.My old HJ holden ute (350 chev) used to launch at

4-4500rpm, run a 1.4 60ft, & 10.1 @ 133 mph.Also most V8s use

a trans & torque convertor which multiplies the torque & literally

slingshots the car off the line.

We are doing it the hard way with Hi-tech, multivalve,turbocharged,small capacity engines - & using solid clutches & manual gearboxs plus hard street suspension/steet tyres.It is much harder than old school drag racing, but it is a challenge, and it is great fun.Dropping the clutch at full revs, changing 4 or 5 gears,keeping the engine on boost,and all the while trying to keep the car off the wall is very entertaining!

There is no doubt that V8s are king of competition drag racing,

but you try and drive a 10sec V8 car on the street reliably.

This is where Hi-tech comes into it's own.They handle well, go like stink,behave on the street in traffic,& have all the creature comforts.Go skylines!!!

:uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-71271
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...