Jump to content
SAU Community

Recommended Posts

I have just (in my brilliance...) backed off all the cylinder head bolts on a S/H rb26 with the ambition to re torque them... which is fine - have re torqued them all to nissan specs and gained a little rotation on the heads bolt which I am satisfied with.

Ok - heres the thing. I did back them all off at once - and there was some residual oil from the head that has tracked out while the head was backed off. Should I have done them one by one? (if I had thought about it a little more before I threw myself at the job this is what I would have done I think). Should I now take the head off and replace the gasket / clean the surfaces as a precaution? The inlet manifold etc is on - I would need to take this off again, But I am yet to put the turbos / exhaust side on.

I am pretty embarresed to be asking about this guys - feel like a major screw up at the moment (what was I THINKING!).... please go easy on me....

Edited by Antimatter

I have no idea, maybe just torque it up and let it run in on idle for a while, that way any oil should burn off? I know what you mean, theoretically im thinking it should be perfectly clean for best result... does it really make much of a difference if you do it now or if it fails later? just leave it and give it a shot, you might even save yourself an afternoon - just keep an eye on those sensors! :D

Remember when your torquing it up try not to stop until you hear that click or start/stop. It can take up to 30% more torque just to get it moving again and potentially give you a misleading reading

Edited by Jmaac

My paranoia has got the better of me.... cylinder head is off... What was I THINKING... "undo all the head bolts at once" ... duh.

Now the question is - do I have a bit of a play with the combustion chambers and give it a nice 3 angle valve cut....

I have no idea, maybe just torque it up and let it run in on idle for a while, that way any oil should burn off? I know what you mean, theoretically im thinking it should be perfectly clean for best result... does it really make much of a difference if you do it now or if it fails later? just leave it and give it a shot, you might even save yourself an afternoon - just keep an eye on those sensors! :D

Remember when your torquing it up try not to stop until you hear that click or start/stop. It can take up to 30% more torque just to get it moving again and potentially give you a misleading reading

After the gasket is compressed, retorquing should only be a slight backoff and retourque.

since you have the head off then look at the valve seats, down the bores, under the head in the squish zones for damage. If nothing needs to be done get a competic metal gasket and put it back together with new head bolts if any of them are different lengths.

Remember when your torquing it up try not to stop until you hear that click or start/stop. It can take up to 30% more torque just to get it moving again and potentially give you a misleading reading

That’s why the degree method using a degree wheel is more accurate than using a torque wrench.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
    • I believe @Duncan has given it a crack at Mt Buller before (in actual race conditions)
×
×
  • Create New...