Jump to content
SAU Community

Recommended Posts

I want to boot my engine up a little, its completely stock r32 gts-t apart from the 3.5" exhaust and the bleed valve... wat should i do next to lift its kw which is in the 600 range. cheers boys.

boost controller probably... dunno how much they are...

-D

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699114
Share on other sites

wat only 600rwkw??

no dude, i have $600 to spend.. i can get a t4 turbo for 500 off a mates cousin. but then i need a new intercooler. should i purchase the t4? and get an intercooler, any idea how much that will lift it?

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699135
Share on other sites

Get an intercooler first - how much you want to spend? Starts from $400-$700+ depends on the brand and specs you want.

the t4 turbo wont be around for long a fair few ppl want it, should i bag the t4 then save for the intercooler? turbos are never 500...

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699154
Share on other sites

How long have you had the car?:)......Be patient dude ..save some more money and then get some goodies and chuck them all at once.

You will feel the difference more if you do it that way. If you put an intercooler now, and thats it, you would feel bugger all difference and you are going to think that you just wasted your hard earn dollars. imho.

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699217
Share on other sites

an intercooler is not a power gain

full exhaust from turbo back? or just cat back?

get a 2ndhand intercooler off ebay and do the pipe work and fitting yourself

look for a remapped r32 ecu off ebay

perhaps a bigger fuel pump and a fuel pressure regulator wouldnt be a bad thing

and a RB25 stock turbo

fir the turbo and intercooler and boost to 12psi, install the fuel pump, get the regulator setup on a dyno with the remapped ecu and you should have a decent gain.

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699226
Share on other sites

an intercooler is not a power gain

full exhaust from turbo back? or just cat back?

get a 2ndhand intercooler off ebay and do the pipe work and fitting yourself

look for a remapped r32 ecu off ebay

perhaps a bigger fuel pump and a fuel pressure regulator wouldnt be a bad thing

and a RB25 stock turbo

fir the turbo and intercooler and boost to 12psi, install the fuel pump, get the regulator setup on a dyno with the remapped ecu and you should have a decent gain.

how much do u think ur lookin at there mate? we talking 2000? or wat...

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699236
Share on other sites

i think i also need a few guages to monitor my engine a little more.. i only have speed tacho, rpm and stock boost gauge, which is 7psi, mines already at around 11... so i have no idea.. do u reccomend obtaining gauges to put into the car?

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699238
Share on other sites

Get an RB25 turbo + Intercooler + fuel pump anymore more than 12psi will require ecu work like a SAFC or remap. If you really want a t4 turbo you will need a t3 flange to fit it

yeah that or you can just put on some hks, nismo, g reddy stickers and that'll add an extra 50kw or so! :)

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699283
Share on other sites

2nd hand remapped ecu from ebay - $250 at most

intercooler ebay - $200

Nismo fuel pressure regulator - $150

bosch 040 fuel pump - $150

rb25 turbo - $200

around a grand I suppose, but it would give a decent power-up IMO

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699389
Share on other sites

Dood, what are you doing??

$600???

Keep it in the bank and focus on paying rent & bills.

Anything major that you do will probably need a decent ecu to cope followed by a tune.

Tune alone about 1/2 grand..........save your money if thats all you got.

Link to comment
https://www.sau.com.au/forums/topic/209201-car-help/#findComment-3699511
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
×
×
  • Create New...